Scheduled Maintenance:
We are undertaking some essential, but extensive maintenance to improve Yahoo!
Calendar. Your Group Calendar is being migrated to a much improved version of
Yahoo! Calendar. During the maintenance period, you may not have access to your
Groups Calendar.
We sincerely apologize for this inconvenience. Your Groups Calendar is in great
shape and we are working to have it available again as quickly as possible
- Yahoo! Groups & Yahoo! Calendar Team
Theo and all, RE:- ... My Colpits oscillator crystal is ~3.6MHz and the pll boosts E-Bus to ~16MHz in my target. Cold start is reliable, in Colpits mode...
7600
robert@...
Jul 1, 2004 8:05 am
Your Mail has been bounced from the OutPost/1.800eMail Server Because "robert@..." is not a valid username Original message, less any attachments,...
7601
Doron Fael
doronf@...
Jul 1, 2004 8:29 am
The Colpitts oscillator is specified in the spec. to work up to 16MHz frequency (not 5MHz as you write). Regardless of the spec, it is a good idea to operate...
7602
robert@...
Jul 1, 2004 8:29 am
Your Mail has been bounced from the OutPost/1.800eMail Server Because "robert@..." is not a valid username Original message, less any attachments,...
Hi ... frequency (not 5MHz as you write). Oops - really misunderstood that point. ... External Reset, STOP and WAIT Power-Down Modes, Self-Clock Mode, and ...
7604
Doron Fael
doronf@...
Jul 1, 2004 10:27 am
... No BDM can support the above specified cases. The limitation is due to hardware limitations embedded in the HCS12 silicon BDM interface, so no BDM can work...
7605
Javier Alberola
javieralberola@...
Jul 1, 2004 11:19 am
Hello, I've written a really simple program to send an ascii character via RS232 and it doesn't work. Can you help me to see the mistake? This is the code, for...
7606
robert@...
Jul 1, 2004 11:20 am
Your Mail has been bounced from the OutPost/1.800eMail Server Because "robert@..." is not a valid username Original message, less any attachments,...
7607
Javier Alberola
javieralberola@...
Jul 1, 2004 11:24 am
Hello, I've written a really simple program to send an ascii character via RS232 and it doesn't work. Can you help me to see the mistake? This is the code, for...
... 15 years ago Motorola said BDM was necessary because of the pin density and number, and it would be as good as an Emulator. To some extent it is an...
... primary cause of "can't abort target". ... the pin density and number, and it would be as good as an Emulator. To some extent it is an emulator integrated...
... Hi Andrew, ... Bit different from my case, 16 meg oscilator no PLL. ... Being aware the circuit is a bit touchy from various messages here, I stuck with...
7611
robert@...
Jul 1, 2004 12:55 pm
Your Mail has been bounced from the OutPost/1.800eMail Server Because "robert@..." is not a valid username Original message, less any attachments,...
Re: My comments ... primary cause of "can't abort target". ... maker or Motorola user of the group has point out that limitation also applies to "wai", "stop"....
... Theo - I don't think so, but it is said to turn the clocks core off. Therefore peripherals run, but I guess the bdm misses some sync pulses? "Wai" does not...
I've got an Tech Arts 9S12DP256 board. I am using the Imagecraft compiler. When I download any of the demo programs I get the error: S-Record Out of Range I...
Anyone out there that has experience with the modulus down counter on the S12? Section 3.3.29 of the S12 ECT block user guide (S12ECT16B8V1.pdf) describes the...
Email off the list and I'll send you the files that I got from Technological arts, they work just fine with me using the same 9S12DP256 board you are using. ...
I found the answer to my problem after more experimentation. The key is to use the FLMC to force the initial delay into the modulus counter and then just let...
... only bit that I set in that register is PLLSEL. So there shouldn't be problem with WAI. ... though that in PowerPC BDM they vitually have to, and I don't...
7619
Richard F. Man
richard-lists@...
Jul 1, 2004 9:50 pm
Shayne, talk to Alex of Tech Arts, he should have the magic incantation you need. I am working with him to make this process just a wee bit simpler later. Make...
7620
Tobias Svensson
Tobias.Svensson@...
Jul 2, 2004 1:03 pm
Hi, I’m trying to get uCOS-II running on a HCS12 from the IC68HC12-patch from www.ucos-ii.com. I’m having a problem with hcs12dp256.h and tick-interrupts. ...
... It's writing an MBA for the possibility of sub logical drives. I ran into that a while back as well. Put some kludgy stuff in to take care of it and ...
Hi, is there a way to generate a reset from software on the 9S12DP256? Shayne C. Rich Microbial Aerosol Biodetection System 1780 N Research Park Way North...
One simple way is to connect an output pin to the reset line. Regards Dave...
7625
jhackett@...
Jul 2, 2004 8:39 pm
Isn't there a reset register? Poke a value. Look in the register table. ... From: Shayne C. Rich [mailto:shayne@...] Sent: Friday, July...
7626
Doron Fael
doronf@...
Jul 2, 2004 8:41 pm
Enable the COP Watchdog, then write a data different from $55 or $AA to the ARMCOP register. This will generate an immediate Reset (the COP Watchdog Reset...
Scheduled Maintenance:
We are undertaking some essential, but extensive maintenance to improve Yahoo!
Calendar. Your Group Calendar is being migrated to a much improved version of
Yahoo! Calendar. During the maintenance period, you may not have access to your
Groups Calendar.
We sincerely apologize for this inconvenience. Your Groups Calendar is in great
shape and we are working to have it available again as quickly as possible
- Yahoo! Groups & Yahoo! Calendar Team
