Terry, Thanks to the suggestion from Bob Denny, the latest version of the TCC (1.5.8) automatically takes care of DCOM configuration. In case you don't know,...
Chris, Thanks for your reply a little while back. It prompted me to hunt for the source code installed with ASCOM, in which I have dug up examples which do...
Hi Everyone, Probably a question that's been asked before.....but I can't find it anywhere. Will Ascom support lxd55 autostar protocall? Is the LX200 protocall...
I will check the version I am using. Thanks for the tip. Terry Standefer ... TCC ... you ... the ... soon. ... choosing ... astronomers ... download ... and ...
... information ... ^^^^^^^^^^ Hope I'm not out of bounds here, but I don't know about a marketing plan that requires you to 'join a club' in order to find out...
Take the time to visit the link, all the info you need is there. The 'club' is just a groups for people to share ideas, questions, etc. This is not unlike...
... The problem is the requirement to join the group to read the messages. It makes sense to require joining to post but I see no reason to require membership...
John, Did you see the response to the last complaint post you made on this subject? There was a response by me and others informing you that even this group...
... the ... You are a "member" of the "club" to post on this group, you know! You may have been grandfathered in when the group was converted to subcribe only...
... This group is not the place to discuss this as it is totally off- topic so I beleive the thread should end here. Since Yahoo groups are optional, you may...
There used to be problems with allowing non-members to read the message archives, since spammers could harvest email addresses from them. However, I think...
I don't beleive that the 55's are computer controllable. Anyone else have better info? -- Bob Denny rdenny@... DC-3 Dreams, SP Makers of ACP and PinPoint ...
Bob, Works like a champ with the LX200 and Autostar driver. I have quite of few user of GuideDog on LXD55 mounts. But guiding is better with the undocumented...
I'm getting some questions about how our new AstroHub can guide these scopes. Is the Meade APM device simply a ground closure input to #M command converter?...
Al, The APM 909 plugs into the Aux port on the base of the LX90. It does not connect to the Autostar. It provides connections for a Reticle Eyepiece, ...
Thanks Steve So the APM essentially is an "ST-4 output" to #M command converter? Does this have the same issues as the GPS scopes where the latency or whatever...
Al, "So the APM essentially is an "ST-4 output" to #M command converter?" No, the APM is an ST-4 compatible INPUT, that is independent of the Autostar ...
is there a instruction manula available ... want to look at it before downloading to see if i can use it. i have a celestron as mount ... the sky 6 .. what...
A camera. If you are currently using Maxim+PinPoint or TheSky+CCDSoft then PAM should work fine. Actually PinPoint+CCDSoft works too. --Tim Long Composed on a...
I meant to say the APM module takes the output of a camera or relay box and converts these to #M commands for those Meade mounts that don't have an auto-guider...
As I understand it, the APM909 module 'talks' to the controller via an I2C 2-wire inter-chip bus. I do not know at what data rate, but I would expect to...
Hello, This post is probably better on the users group but I figured I would post here while my membership in that group is being reviewed, I think all the...
Hi, Peter, There should be a manual available with the download, which you can get to from here: http://users.bsdwebsolutions.com/~larryweber/ Yes, you need a...
I am making a preview release of my Sphinx driver available for comment. This update adds slewing and guiding features and requires firmware 1.2 build 24. It...
I've posted the following message on hnsky yahoogroup Somebody could help me, indeed the problem could be related to Ascom/POTH Thanks Pierre de Ponthiere...
Dear all, I am using a ACP 3.3 licence for local use. I am afraid that my ACP installation will be spoiled if I install the trial version for testing the web...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
