Hi, I'm off to plymouth for the week, so wont be posting any time soon, hope you're all well and stay that way :) Kind Regards, -- <tsb> <sb>*Alan Fisher* ...
Hi, ... Everyone`s off on holiday except me :( Anyway just to say that I am still working on the Coldfire card, I will put some information on it soon, I am...
I just thought I'd mention that Dave Haynie still seems to be reading the wild rice coldfire emails. He answered someone's question about implementing an ATA...
In a message dated 7/9/02 4:45:28 AM, jamesd@... writes: << I just thought I'd mention that Dave Haynie still seems to be reading the wild rice coldfire...
Hi, ... Ermm, No, sorry... Had a rest last week when a relative came down to stay but he has gone now, I have been working on my Coldfire web site (Nothing ...
Hello Oli_HD Hi I'm back from my holiday, I have managed to get a load of cables (IDE) and copied across my old boot partition, so my A1200 is after a fasion ...
Hi, ... Welcome back, I hope OK. ... Fine, Been working hard as always, Been looking at the £100 V2 coldfire board by Motorola that replaces the 68000,...
Hello Oli_HD ... I'm very well thankyou :) ... V2's iirc are not all that powerfull (I seem to remember them being likened to a 68030 of a similar speed), why...
Hi, ... Very true, there are 16 and 25Mhz V2`s if I remember but it is basically what we want out of a card, It adds a Coldfire CPU to the Amiga, Upgrading...
Wow, new messages! Almost couldn't believe it! Any news on the investment funds from a certain Japanese company? (ROTFLMAO) Say, where's the info on the V2 to...
Hi, ... Yep, Its been a little quiet but then again there isnt that much for me to say at the moment... ... Ermm, No... (Dont want funding anyway...) ... ...
In a message dated 7/23/02 3:13:52 AM Pacific Daylight Time, club@... ... Well I know where ur going with this....been down this road before. Right ...
On8142@...
Jul 23, 2002 5:57 pm
1041
Hi, Just wondering if anyone is going to the Amiga show in the US. Know its costly, but maybe we could all meet up and work on this project??...
On8142@...
Jul 25, 2002 6:36 pm
1042
Hi, ... I think I will pass this time :), The US is a little bit to far for me to travel. (And like you say, Very costly) However I will be attending all the...
In a message dated 7/25/02 1:03:56 PM Pacific Daylight Time, club@... ... Kinda thought so....rather have ur funds go into work on the card anyhow. ......
On8142@...
Jul 25, 2002 8:22 pm
1044
Has anyone taken a schematic in Pdf format and pulled it out and used it in a Electronics program? How do you do it? jb...
On8142@...
Jul 27, 2002 1:49 am
1045
If it's from a scan, you re-enter it by hand. ... used it in a...
In a message dated 7/26/02 10:58:18 PM Pacific Daylight Time, ... Oh no ....got to be an easier way.....what happend to cut and paste or drag and drop...lol jb...
On8142@...
Jul 27, 2002 4:09 pm
1047
Hi, ... There are lots of PCB printing companys that offer magazine lifts, a PDF document would have to be done the same way. ... There has to be a package...
Hi, Just to say that the flash chips will be here tommorow, I should then have all the components needed, and excluding the PCB (I need to get the chips to...
Magazine lifts are done through photography, not by turning the thing into a file that can really used in a board layout program. You'd be doing layout by hand...
Hi, ... Its 8 MB (Megabit), I will be using it on a 16bit bus so thats 512Kb which should be overkill for all my needs but if not I can always change it to an...
Hello, ... When you use this part as 8 bit it is wired up differently for the address lines, the A-1 pin connects to A0, A0 of the device to A1 of the databus...
... Hmmmm... I know I have heard that name before, just can't remember where. ... have a ... work as a boot ROM. ... from the low order ... The new ROM has to...
Hi, ... Thats why CS0 is used, when the Coldfire powers up it will look at whatever is connected to CS0 before it checks anything else so if the emulator is...
Hi, ... Yes, I know, I "really" dont think I will need to run it in 8 bit, There were lots of 8 bit only parts available (Why are people still using 8bit...
Hi, ... there is a bit missing here isnt there :) Sorry, This reply has been dragged out and has taken all day. What it was ment to say was: I have yet to find...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
