Hi, Hope this is alrite !!! Am a part of the recruitment drive with one of the leading IT companies in India and abroad. We're right now looking out for...
Dear Madam, Here attaching my CV in response to your email. I hope you will give me once chance to prove my seld Regards, Vishal seethamk <seethamk@...>...
Rane, You will have to email your Resume directly we currently have attachments turned off. -Rick Would you guys prefer the ablility to send attachments turned...
why are you changing route patterns to restrict a group of individuals? Better to create a new cor whose FRL cannot access long distance route patterns. ... ...
You can change this but it is a system wide setting. On the first page of the trunk form there is a field called outgoing display. if your admin strikes this...
You can change this but it is a system wide setting. On the first page of the trunk form there is a field called outgoing display. if your admin strikes this...
Anyone have an IP installation in their office? We are runnning a story on the 4600 series phones tomorrow, I Just wanted to get some feedback from actual...
I'm having problems with message indicator on my stations. I have a Definity ver 8 and a non Audix Voice Mail System. This one is a Key Voice and the interface...
I'm having problems with message indicator on my stations. I have a Definity ver 8 and a non Audix Voice Mail System. This one is a Key Voice and the interface...
I apologize, I made my question in wrong way. The case is this, we have two Definity's in different location, these are connected via E1 link (30 channels),...
Simply configuring the trunks as ISDN-PRI to connect the switches is not a proper networking environment - you must also use either Avaya's DCS package or...
Have you set parameter in D-channal signal group . Because on page 2 you must fill some parameter in TSC signal , and then in ARS table must fill the ND number...
I am having trouble transfering a call that came in on one trunk group and transferring out on another trunk group. I have a Definity Prologox and I want to...
I don't have experience with that specific pbx, but have you looked into setting UDP's...for us the command would be "change udp xxxx" (xxxx being the...
Telecom Support
TelcomSupport@...
May 24, 2002 1:26 am
195
Bob, Did you find out how to do this yet? Before you do this, I have to ask, are you aware this will be a security risk, and a big one at that? There are a...
Hey gang, We installed a ISDN PRI circuit a couple months ago. I happened to be doing some testing yesterday, making concurrent inbound calls to a specific...
I believe that it will allow 1 less call than you have call appearance buttons. It reserves the last call appearance for transferring, calling out, or...
Correct, the switch will only allow 2 incoming calls with 3 call appearances, or 4 incoming calls with 5 appearances, and so on. You can also set the...
Thanks Pat and Brian! I tested this morning by adding a 4th call appearance button and the 3rd call rang in fine. I had incorrectly believed that when all the...
"Stan W." wrote: I had incorrectly believed that when all the call ... to cover. Stan, do you have a coverage path setup for that ext. with a valid coverage...
... Brian, There is a coverage path on this ext. with a valid coverage point (standard voice mail hunt group). The busy is set to "n" on both inside and...
<P>Stan, <P>As you already know, additional call appearances will allow additional calls to the station; depending on your software you should also be...
... The busy is set to "n" on both inside and outside calls though. Does this need to be set to "y"? Stan, if you want calls to rediret to coverage on a busy,...
As long as the trunk that he's trying to transfer the people over is simply a tie trunk to another part of their facilities, then there shouldn't be a security...
Telecom Support
TelcomSupport@...
May 29, 2002 12:12 pm
205
You need to assign more "call-appr" lines to the phone. Also, that last line sounds like it is being reserved. When you do a display or change station, take...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
