Hello, This email message is a notification to let you know that a file has been uploaded to the Files area of the Bedini_Monopole3 group. File :...
Bedini_Monopole3@yaho...
May 15, 2006 4:56 pm
2
Hello, This email message is a notification to let you know that a file has been uploaded to the Files area of the Bedini_Monopole3 group. File :...
Bedini_Monopole3@yaho...
May 15, 2006 5:16 pm
3
Hello, This email message is a notification to let you know that a file has been uploaded to the Files area of the Bedini_Monopole3 group. File :...
Bedini_Monopole3@yaho...
May 15, 2006 5:26 pm
4
Hello, This email message is a notification to let you know that a file has been uploaded to the Files area of the Bedini_Monopole3 group. File :...
Bedini_Monopole3@yaho...
May 15, 2006 8:46 pm
5
Sometimes people send emails to the moderator instead of the list. Please post your questions to the list. Here was one: "Can the rotor (wheel) be horizontal...
Hi, I finished the setup. I am using coat hanger wire instead of the welding rods, (they are their way ) The wheel is rotain, but i am not gating much energy...
Ken, Good to see you finally got it going. You must have something not hooked up correctly or have really bad batteries or have blown a part (like a...
Hi, Can I send a jpg of my circuit. Anyway I did not solder he wire to the transistor. I used a breadboard, and for the collector I used a clip to hold the...
Hi, Just cuz the coil repels the magnet does not mean it is wound the right way. It can be wound incorrectly and still be wired to the transistor to repel the...
hello, I just check the winding like you explain and luckily it is wound correctly. From what you are saying the source battery always decreases in potential....
Gene, I'm not sure if I can state it clearer than what I have. The only thing in addition is that when you wind the coil as I have said, you end up with the...
Hi, I put up two pictures of my circuit.¸ Also , I am still waiting for my order of R60 weldind rod. I am using coat hangers now. I think I should wait for...
Hey, I had order some R60 rod like I told you guys. Man i was suppsee to get it last friday. Called them today, now they are back order for another week,, so...
HI, got my Rod yesterday: RG60, same as R60. I think I am getting better repulsion with this, but not as much as I thought. Anyway I have two 12v battery...
Looks like your one battery is warn out by the looks of it. This can happen by abuse, long life sitting on a shelf, long use with conventional systems, or by...
Hi, can you upload the plans for the Bedini's solid state pulse charger. Also, I tried other 12v batteries ( 3 in all ) and they all do that , they discharge...
Ken, I said all I did because you shared that the other battery did not discharge very fast, but behaved normal and discharged slowly. If that is the case then...
Hi I bought another potentiometer. I think mine was not good. Now the motor is turning much faster then before and the source battery is discharging at a...
Ken, You can burn out these pots easily if you turn them too fast under operation. The long safe way is to turn them only when the machine is not moving, or...
Hey, I dont have the discharge problem anymore. Although I am hearing click click noise from the transistor. That is happening only when the charge battery is...
Ken, Good to hear. Do not remove the charging battery while running as this puts tension on the transistor and can burn it out if done for long enough. There...
You can use about any size rotor over about 2 inches, but when you go really small it can get difficult. The best to use is the biggest aluminum rimmed wheel...
Al, The magnets are very common. They are sold at Radio Shack in the USA or are known as domino size magnets. I get them cheep from AZ Industries with a...
hi,, i finally got the rotor going, i used power supply adaptor first, but no battery for charging.. i used my small magnet, since it took a fast push spin to...
hi to all again,the setup ive made has a problem, it does not charge the 2nd battery, i dont know why, is it wrong to use a power supply in this setup and the...
Hello alfrancis, What have you done so far in the way of diagnosis? Have you walked through the circuit with your voltmeter to verify that you are getting...
hi luther, thanks for the reply, ive been waiting for an advice since the motor start to spin... my diagnosis is this, for the meantime ive been using a power...
Francis, I don't have much time right now so maybe some others can respond in more detail. You may want to just keep with the same batteries and start with...
Hello Alfrancis, Just have a couple of things I want to discuss. First off, it looks like your power supply should be fine. At 500 milliamps and drawing only...
Hi Francis, I had problems trying to charge NiMH with my SSG. Although the voltage in the batteries appered to rise while the SSG was running as soon as the...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
