Marco, No need to worry about questions. That is why I created this forum. Yes, the neos will saturate some iron cores. Even scalar magnets made with ceramics...
Thank You Rick for Your quick answer. As per Your suggestion I've checked further the circuit finding a miswiring (running battery+ was NOT connected to the...
Some of you will already have John Bedini's and Tom Bearden's new book. I'm selling it presently for $33 on my website (which I will soon raise the price a...
Hi Rick, I have this new book. The diagrams for the solid state one are the same as in the freely available patent, I don't see why they should be kept secret...
Welcome Dave, No, you need to read the book a little more carefully; the solid state oscillator charger is not shown in the publically viewable patent. I mean,...
Hi Rick, Looking closer I can see the 555 timer works but the pulse time is about 2 seconds on, and about the same time off. This just seemed strange as there...
Hi there this is Eric from Oregon. I have been lurking in many dissusion groups relating to alternative energy generation from water fuel to this group in...
eric, great job!! i don't think you need to fine tune it any further, sounds like you are ready for the load testing. some comments.. don't remove your charge...
It runs great and seems to charge but will not continue to charge Batteries. After three charges and discharges it just gets weaker And can't build up just...
Hey... try increasing the gap distance between the stator and the rotor to reduce the current needed to maintain rotation of the neos. (or just build another...
Rick- I used welding rods instead of a solid steel core like you told me. -a 9 1/2" lawnmower wheel (plastic and rubber) for the wheel -a handmade spool from...
Hi all, Can anyone tell me generally how many charge discharge cycles it will take before the battery will start to give out more that it took to charge it and...
Hello, My name is Jerry from North Carolina. I've spent the past few weeks reading Bedini's and Bearden's sites. I've also been lurking in this group more...
welcome Jerry, #20 will work fine. stay with the 850 turns or so. Jason qhorin0 <pjm5759@...> wrote: Hello, My name is Jerry from North Carolina. I've...
Hi Dave, First of all, if you're using new batteries, in my experience the charging battery will give out more than you put into it right off the bat, but...
Hi Jerry, The #20 should be fine. Look up an AWG wire chart that specifies resistance per 100-1000feet and just figure the length of #20 needed to put a...
According to http://amasci.com/tesla/wire1.txt #20's resistance is 98.496 Ft/Ohm. Just to verify before I start coiling: To obtain the resistance of .6-1 ohms...
Hi Jerry, After reading the material list against the Schematic sheet you will notice there is a difference. Schematic reads #23 power coil and 26 trigger...
Hi Matthew, Thanks for the advice. May I ask then, what if my battery doesnt reach the predetermined charge level with in one hour? Shall I just wait until it...
Hi Jerry, I'd use the value of 10.153ohms per 1000feet. Not sure how to read the Ft/Ohms, that must be feet needed to reach 1ohm? If thats the case then you...
We've said it 1000 times, you can't use those magnets on this setup. They don't match the coil and core. You will saturate your coil as you have done. Those...
On this list we are not getting into the theory or modifications, only rarely. I will say that yes this is the simplest way to charge batteries the best way...
In the notes for the tests there is given at least two options on how you can run your test(s) to determine cut off and/or charging times or voltages. It is up...
For the record I am not behind anyone's comments on the SSG group as claimed. I am also not trying to hinder any progress made on that list. However, it hasn't...
Howdy, I've not been on the SG list for a good while... now I think my time has come to leave this group as well. Its been interesting and the devices DO work...
agreed 100%... except i have a solution to find useful information. i painstakingly copied every post that john bedini & peter lindeman made on that message...
I did a little demonstration for three athiests at the university of Florida on Friday with my little tape motor setup and I wanted to make some clarifications...
Just a question while I wait for parts for the basic system I did get the book and saw two setups one with a wheel and on without, is the on without the solid...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
