I now have a working unit, and I made my coil with 500 turns of 18 and 24 magnet wire wrapped together around the coil. I read in this forum of people...
Hi Wes Duda, 1. if I'm twisting a few wires together, how tight they should be? sometimes vendors refers to so many twists per liner inch of twisted wire,...
Hi guys, I noticed that on the home page the picture of the schematic now shows a MJL21194 instead of the MPS8099 that is shown on the schematic that gets...
John and new members, Read all of my emails on this list for all the directions. The MPS8099 is very small and is only for a small setup and using 9v ...
These magnets are about 3 inches in Diameter but have a hole in the middle, I read on another post here that small ones some other person was using had one...
sounds like you're on the right track. when mounting the magnets make sure the North pole faces outwards for all magnets. there should be a space of about...
Hi Rick, Thanks for the response. I have taken your advice and read through all of your posts on this list. (About 156 of them) You must get frustrated...
Hi Don, I seem to recall John B. or Rick saying no to holes in the magnets. They do not work properly in the present invention under study. I think if you do a...
Greetings! Started rotation at 8:00PM. The 20" 20 magnet machine has been running for an hour already. The batteries are 3-year old marine grade deep cycle. ...
First of all, I'm very excited, and who would understand what is going on, but people in this group. Thanks. After winding my coil, just as described in this...
Hi Group, I have re-started my load testing since I changed the coil core to welding rods. (As they should be) You can see my results so far in: Files >...
Wes, You are NOT supposed to ground this device to anything. You would consider it a "floating ground" circuit. Connecting this circuit to a conventional...
Wes: Could you describe where you attached the ground to the SSG circuit? Also, could you describe the actual ground in some detail? Isn't it great to have...
Now you got me….. I was so happy having such good results. I bought the new book about free energy, but the thru is I can not understand everything even I ...
I attached the ground to the (-) form prime battery, Marcia told me that you not suppose to use grounding... But there are other people who are thinking about...
Dear Wes, It does not make sense for a person like me who is only taking baby steps in Mr. Bedini's classroom to comment on other people's schematics. First I...
Here's the story of grounding. First, stick to the basic setup until you are fully aquainted with how it works and what you can do. When you rightly understand...
[The below messages were posted before I finished my last email. Wes, keep at your research. But do not stop short of finishing with the objectives of this...
FWD: from my Bedini Window Energizer group. Lets see everyone put the same effort into it. I have told you that you can take the batteries down lower, but for...
Marcia, I'm not able to see the pictures on either groups. Rick ... path=/Marcia%27s%20Files/ ... engrossed in doing experiments that I forgot to post the...
Hello! I was tying to tune my wheel yesterday. I played with the gap in between the core and the magnets (got it a little higher to see what it did) and my...
I'm sorry people have had trouble viewing these graph images. It seems that YahooGroups is performing some logic on certain things I upload, creating...
Greetings! The 20" wheel takes 90 seconds to stop after batts disconnect. After 16 hours running,both batts are .01v higher than when I started. I swap them...
Charles, Go clean out your bearings of all grease and put in some xcelplus spray and see then how long it spins. I had one that would spin over 5 minutes after...
Hello Rick, all, Just need to ask how free-wheeling should the wheel be? Should the rotor be totally free of load? I thought some load was beneficial for the...
Hi Don, I sure would have liked to see a ferrite magnet placed in the rotating field with the ferrofluid placed around magnet as external field is turned off...
Lester, Your wheel is fine. I was just saying you can get less friction in many bearings with cleaning them out and adding xcelplus. But if it takes 300ma then...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
