I had soldered the components into the basic circuit day before yesterday, then hooked it all together with the insulated test leads. Spun the rotor, got nada....
Thanks, John. I thought it might've been something obvious to everyone but me. Can't do pix just now, as I tore everything completely apart yesterday. It...
Hi I am putting together my first SSG now and I just finished winding the coil. Its about 1 5/8 tall and almost 2" in diameter with a 3/4 hole down the middle....
V, The specified size for welding rod thickness is 1/16", but you may go 50% smaller or 100% larger, so your 1/8" will be fine. Just pack in as many as you...
For those here in the states, Harbor Freight stores have boxes of 3/32" rods for $4 on sale right now ... From: John Koorn <john_koorn@...> Subject:...
Ahhh, it happens mate. Rebuild it all and post some pics etc. John is right, and it sounds like you may have damaged your transistor. Funny that it was heating...
Group, I have uploaded the new Monopole SSG Building & Testing instructions to the Files folder. It is called: "Bedini Monopole 3 Group Experiment V1.00.pdf" ...
Woodntya, I was replicating Rick's SSG self-runner, exactly the same. I wanted to make sure I could get it to work just as Rick had before I changed anything. ...
Hello to every one, I've built a bedini sg, and now im making the load test, i only have 1 batery, and it's dead, but i guess that i can do test to see if the...
Hi alvaro.hernandorena, Normally you should never discharge a battery until its totally dead like that. it will destroy the battery. Discharge it only till 12...
I finally got the tachometer and yesterday I measured the speed of my monopole motor. It is 186 rpm on 0.08A, 12 V and 360rpm on .21A, and 12V. Other people...
Hi ebisevac, How big is your wheel. if its a bicycle wheel then you have plenty or RPM. 10000 Rpm is only for very small wheels. if you run a bicycle wheel...
Hi V, It is 13" reel wheel. This is my you tube movie http://www.youtube.com/watch?v=X2KKH8dABQg Thanks, Erkan ... From: V <lights@...> Subject: Re:...
Hi All, I have set up a Bedini SSG and have it running nicely at around 320 rpm and about 160 mA. That was my peak in the rpm/mA ratio. That occurred at a...
Hi Chris, Well done on getting your setup running. Regarding your question about battery voltages. You are right in that some portions of the charge cycle take...
Hello Chris, are your batteries sealed gel type ? I am currently at the same stage as you trying to figure out what voltage setpoints etc to use.I was using...
Hi V, tank you for the advice,last night i dischargit untill 12v only and then charge it again and it took much more charge Amps i supoose but i can't tell (i...
Hi V, Hey it works, I only have 6 volt batteries right now , but will got the new 12 volt ones later. seems to be charging the battery just fine. Lost the neon...
Hello, i was looking at the pics in http://www.icehouse.net/john34/kron.html and i don't under stand why each coil has 4 transistors, i've read that for multi...
Hi, When you have 4 transistors, the slave coil have one winding by transistors so 4 windings. And for the trigger coil, this coil have 5 windings, 1 winding...
New pictures uploaded of the new 5" Brushless Fan Energizer Kit: http://rpmgt.org/order.html This is a square cage frame rather than a round one. This makes it...
Hi all I have achieved rotation about 2days ago, my excitement was so great that I've blewn up by now 3 npn TIP3055 transistors trying to measure current,...
John, Just read the new instructions you did for the group and I must say that you guys are awesome!! I know how much time it must have taken you, and thinking...
Fantomaslord, Glad to hear of your success. May your realizations about this circuit keep comming and forever change your perspective for the better! A word of...
Hi Michael, Good work. I just looked over your files. So you could see that on most occasions you achieved a battery COP>1.00 (average COP of 1.14). It was...
if i wanted to construct a trifilar coil and run it as the "proud mary" set up, i have a question. there is one trigger and two power coils. how do i connect...
I found this Bedini schematic for slave coils and it just has one transistor per slave coil.... http://www.fight-4-truth.com/Simple%20MP%20Machine.jpg ...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
