Hi, All Today I was succeeded in running my first window motor with sequential bipolar switch and upload the photos on JANG.Y.D's window Motor. As a beginner I...
Hello guys, a question for the more experienced members.What is the comparison from tunning and charging point of view between a SSG using a 21 inch bicycle...
Hello David, I can see your point.So is the current measured on the output meter part of the cause of the the output battery charging or is the current...
Thank you, John. I see I still have some work to do in understanding all this clearly. The connection to the negative battery terminal has really been twisting...
Hello Phillip, When I initially started the experiment, I used inverters. Marcia recommended I not incur the expense of the two additional inverters I planned...
Rotor diameter makes no material difference from a tuning standpoint. However you will note that for the same circuit, a smaller rotor (having magnets set at...
... Having built with an 8 inch wheel, I can say for certain that the speed is higher. In addition, just a cursory comparison of my charger with those made by...
Hi Joe, I think you do have a point about the charging battery being the load. So at the moment, I am a little confused. Looking at the Primary battery, the...
Ok thanks.Think I will reduce number of magnets on my bicycle whhel and see if that helps. Joe. ... Bedini_Monopole3@yahoogroups.com, "everwiser2000"...
I cant seem to get the wheel to turn.. I have tried rearranging the magnets, swapping the poles around, putting fewer and more magnets, alternating the poles...
At some point you fried your transistor. Rick ... the magnets, swapping the ... N,S,N ect.. I have the ... rechecked the circuit about ten ... precision...
Or his diode is backwards. ... From: rickfriedrich To: Bedini_Monopole3@yahoogroups.com Sent: Friday, August 01, 2008 2:06 PM Subject: [Bedini_Monopole3] Re:...
... Just for kicks I tried that too! I have the cathode and anode on the correct ends, I tried turning it around once, it melted my coil housing and shorted...
... I just went and opened a new diode 1N4007 from radio shack. The thing is shorted right out of the package, I think I got a bad batch of parts. Thanks for...
Maybe it is an isolation problem? Two Transistors on the same heatsink or like that? We try to guess. Maybe do the "Mother test", take your mother (neview,...
... It looks great. Good to see you were successful. How do you have your external load hooked up? Exactly as the schematic? ... sequential ... even ... ...
Hello Joe, Michael, I'm not exactly sure what you are asking, but I will endevour to provide some answers (opinions). The SG circuit is little more than an...
Also, when I do my first tests with a new circuit, I put a car halogen lamp in series to the supply battery, so a short will simply just illuminate my lab and...
Hi, I will check it again next monday. It could be wrong but WM with half sequential circuit could charge the secondary battery and WM with full sequential...
Hello Group, So I might be able to put a large farad capacitor or larger in parallel with the battery and the load to raise the power factor phase angle, it...
did you by any chance make the connection to the potentiometer on the outside pins of the pot? this will give you 1000 ohms no matter where the dial is...
My first experience was similar. Here's what I found, hope it helps: 1st Problem was that the magnets passing the coil were not inducing enough current to turn...
Easiest way is to take an Ohm/VOM meter and check for continuity of the pairs of leads, then make sure the (+) positive and (-) negative polarities are...
Ugh! How many mistakes have I made so far? How many hours did I fuss with it to get it running? The coil was ok, but there was a bit of clear enamel left on...
Ok. I know that some people use a power supply to run their sg's, so is it safe to assume i can use a car battery to run my sg, to charge a smaller battery?...
Thanks for all the help I got it running about 20 min after my last post. Turns out I had serveral problems. Any way I had a bad diode, the coil wired upside...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
