Shane, http://www.keelynet.com/bedmot/bedmot.htm Please Note:- I have put this up for historical information only, as it should not distract from or cause off...
John, on several pictures at the internet as well as in Johns Book the SG has some big fan blades attached. As far as I have understand the matter the radiant...
Stephan, The demo of attaching the fan blades was to demonstrate that the SG does not require more current to cater for the load as a conventional motor does....
I thought you could replace one of the batteries with a large capacitor but I think you have to set it up to discharge at some point. This just something I...
Stephan, Like John said, the monopole can do SOME mechanical work, the interesting thing is that amperage does not increase when the shaft is loaded, that is...
You just need another type of load to replace the charging battery. Appropriate sized light globe will do the trick, or maybe a speaker :). You can use a cap...
It isnt that i dont want charging on the backend, i am not planning on changing my ssg whatsover. I just remember seeing a bedini motor that used no primary...
hmm. Ok, I havent seen a monopole that just ran off capacitance. I was answering your original question that simply asked how one could remove the charging...
Oh, your right, and i appreciate your answer, i was just responding to your comment about getting rid of my charging battery is all. And as i said, i might...
Hi All, I have completed more COP tests using a resistance of 1216. 1.77 0.99 1.13 1.76 1.22 1.01 1.28 1.14 Average COP = 1.29 These results are not...
Any COP over about 0.6 is wonderful and very remarkable. Your COP >1.29 if verified would have the physicists jumping out of their shoes. Such a result...
Hi Marcia, I didn't mean to say that my results weren't remarkable, but it has been said that lead-acid batteries do fairly well. I've gotten over 2.0 before ...
Michael and all, It should be noted that during any particular cycle, a battery can be made to provide a very high COP (5 or 6.) It isn't hard to produce COPs...
Thanx for the info on that. I don't remember exactly where I found the 2 amps info. Think it was in the SG group where they discussed multi coil setups. John...
my 5 ah batteries took 2 days to charge, the finish voltage before resting was 14.5 some simple calculations ( I dont know them) would tell you how many amps...
Hi all, yesterday I played around with a LED and a 330 Ohm resistor. I put in series it across the run coil to light up exactly when the run coil shuts down...
The fan has a "NSNS" four pole ring magnet. The fan did run as an SSG with original winding (cca 0.07mm wire two unifilar windings cca 2x 18 feet of wire) the...
Hello Michael, your graph looks similar to mine except my sweet spot is between 3 to 4 h wave pulses.Cop 1.29 is good in my books any thing above 1 is in my...
Hi Dennis, your are right in many aspects you describe. But we should be very carefull what we put into any equation when it comes to COP figures. From my...
Hello Stephan, I did a simlar experiment and saw same results.Think it may only apply to bigger multicoil setups current dropping when load applied. Joe. ... ...
Hello All, a question for more experinced members.What is typical COP figure for a SSG tuned correctly on a 12 hour charge.Also does anyone have a figure for...
Think of it like a paddle wheel in a moving stream. The paddles aren't the source of the energy, but they translate the existing energy flow in to a...
Hi, I read through lots of papers today. JB once said it's all about impedance. This is valid for the SG, the G-Field Generator and many other devices ...
Hi Joe, I have two 11.5 amp hour regular lead-acid batteries. So I am not presently using a power supply on the input. These runs are long runs, most runs are...
Hi Joe, I am interested in this question as well. Here two comments from previous posts that might give an interesting clue on the answer. Tom C in message...
Hi Stephen, Just to clarify, we are not measuring "Battery COP" nor are we measuring "System or Overall COP." We are measuring COP based on a simple formula as...
Michael, here is why I posted about "several" sweet spots. my first sg had 2 spots one at 35 milliamps current draw, and one at 80 milliamps. what do I mean by...
I apologize to all, I made an error: On Tuesday 02 September 2008 13:35, cest73 wrote: (snip) ... (snip) The normal fans are wound bifilar (!) with adjacent...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
