Hello Rick and all, My name is Randal Triggs I live in Brisbane Australia I am a electrical technician. I have made a bedini sg motor and finished the...
My SG motor is running well. 16" wheel with 12 ceramic 8 mags. Coil might be a litle strong. It seems to be most efficient at about 210 rpms and 375ma. That is...
Donald, Welcome, No worries about the higher ma draw. That is just a bigger setup. Initially the basic load tests were for small setups. You are not supposed...
Rick, Thankyou for your great help. I have one additional question for now. "Get yourself an ANALOG current meter and put it in series iwth the 2ndary battery"...
Hi Donald, The prior is correct. It should be connected in series on the positive terminal. One leg to the diode as you noted and the other to the positive...
<http://www.mitedu.freeserve.co.uk/Prac/prac.html> Hi Donald, Pardon for my interruption. I too am new to the Bedini technology and even more new to the field...
Hello Donald, The first way of connecting it you describe is correct. You want it in series with the positive - not going across both the positive and negative...
Hi Don, Thanks for the encouragement and the info. I've done a few other replications from Fuelless.com but the help has not been available from them like it...
Greetings to all, "Multiply your input energy figured in step 2 (watts) times 3600 (or your arbitrarily decided charge time) and you will have your input power...
New objective for this list. A Real Gold Rush!!! 1. Can we prevent the usual lessening of capacity in batteries over time? 2. Can we improve the capacity in...
I may add some clarifications to this from time to time. Here is one: The load should also be fairly high wattage to get the ball moving. Like 100w bulb off an...
Finished building my Sg but have not got it to run yet. Will it work with 9v transistor batts? my 12v 12ah batts are on the way. 21" Diameter alum. cycle wheel...
Hi New Guy... haha It should run off the 9V battery, just likely slightly slower once it spins up. A simple way to verify everything is phased correctly is to...
... it spins up. A simple way to verify everything is phased correctly is ... terminal to each end of the power winding. Make sure it repels the magnets on...
hi to all, can anybody help me explain about the battery being charged so quickly, and the input battery doesnt discharge at all, i dont know what happened?...
Alfrancis et al; Some people have all the bad luck, but don't try to explain, just run your tests and collect all of your data. I am sure some one will ask you...
... if it isn't broken, don't try to fix it. keep running your tests, take maticulous notes, write down how you built the device, your observations etc. you...
I'm not an EE by no means, I'm a car and motorcycle guy. I know that when wiring things up you should connect, Red to Red, Black to Black and Blue to...
Glen, Yes we are dealing with cold boiling here, and noting temp is a very important observation. As for oscillating with the circuit shown on the front page,...
I noticed in the origanal drwings that there is a ground. Earth ground? I asumn it is not needed for this (ssg) to work as Rick does not mention it. Just...
hi jason, fair question. the quick answer is no, it is not necessary to connect anything to Earth ground for the SSG to work as claimed. on other message...
I got my first ssg running this weekend. I had it rotating last weekend but blow a transistor. I now four charged 12v batteries and I started with three dead...
Hello Jason, Congratulations! Great job! Can you describe your replication? What did you use for a rotor and spool size, wire size, magnets etc... Yes, by...
you're off to a great start! let me ask you something, when you blow your transistor what did you learn? or in other words, how can you prevent that from...
My Rotor is an 8” plastic scoter wheel from Wal-Mart ($8 with tire). (5) radio shack magnets (approx. ¾”x1.5”). My coil is not to spec on the sheet. I...
Hello Jason, Thanks for posting the details of the construction. Yes, it indeed does work and works quite well. As your batteries become better conditioned,...
and what protects the neon? ok, i won't make anyone work for it. put a 5K resistor in series with the neon to limit the current. slloyd ... does work and...
Thanks for that tip - I've never put a resistor in series with the neon bulb and haven't burnt one out yet - although one side does have a dark cloud around...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
