Hope we have cleared away the train wreck and are back on track: But facts appear to be this: I did see an unusual effect. The energizer was drawing 7.2 amps @...
An interesting view from jmi; "I'm quite sure you say "12 V" and "24 V" from the battery ratings, right ?Actual measurements would show more decimals, and...
One final blip, RS has offered to help us when we get off target. Apparently he has trouble watching the blind lead the sighted. I have a suspicion he may be...
I'm still not clear on the attractive versus repulsive... seems this would always be setup in repulsive mode... the difference being the power required to run...
... Gene, Yes I think you must be correct from what has been said. I honestly can't decipher correctly at times what John means in his explanations. But is...
Ah gotcha man, I couldn't get the big SSG to run off my 7Ah batts either so I have that laptop supply that gives 16V to 4.5A... that works well... I tried to...
Take a look at the picture in the Vlusta Photo file. This was taken off a small motor we were playing with. The Scope is an old 250Mhz industial scope and...
Dave, Mine has always been in repulse mode... and I saw something of the effect but not on nearly so large a current draw. My little DC motor does 200mA and...
as a matter of fact I saw that today when I was messing around tuning a output SCR(instead of the output diode) with high resistance. How did yours happen? I...
... Joe, The trigger wave is still the same if taken right off the trigger coil. I get a square wave if across the resistor. But you appear correct about the...
... Oneness, We did this last year when we were trying something that Roamer said. Our understanding of what he meant was that if the output capacitor in the...
For those still working on flux gates and g fields. There is a schematic of Kromrey generator added to the Vlusta photos, not sure if this is the converter...
You can actually just create a static tank with a winding and a diode and a cap that you don't touch so as to leave that energy sitting on the stator. Don't...
... diode and a cap that you don't touch so as to leave that energy sitting on the stator. Don't discharge that cap and make sure its capable of holding...
Hi Dave, Thanks for the reply. I have triple checked the transister and i have got that connected correctly (The doco for it is very poor unfortunately). So...
... everything from: Nat, Just go to http://peswiki.com/index.php/Directory:Bedini_SG, Follow the information there. You can't miss. :-) hopefully. ~ dave...
captpjk asked what is a G-Field. RS wrote: "The G in G-Field means "Gated" Flux, so it is a Gated Flux Field. Use the full patent pulser with a G-Field's...
Dave, yes, I had a similar looking reading on my scope when I once had a shorting between the different windings somewhere in the coil because it got too hot. ...
Gene, I have trouble in understanding the first part of what you say. How could you leave the "energy sitting on the stator", the diode is either so that it...
David, Thank you for your description, it is most helpful. Patrick ... captpjk asked what is a G-Field. RS wrote: "The G in G-Field means "Gated" Flux, so...
... stored in that cap then and not still sitting on the stator! Gene, I think you too may be trying to achieve the effect Roamer speaks of. Our understanding...
joe_1001101 wrote Joe I reread your post and realized you were interested in how the attractive mode functioned. I was so flustered about screwing up modes,...
To Anyone interested: Maybe the simplest way to understand flux gating is the photo of a simple gate in Vlusta Photos called "Flux Gate". A soft iron ...
hi all, does this help? This is particularly interesting since, with a permanent magnet, one can apply spatiotemporal (G-Field) stress in a locality without...
When I scoped my motor with a dual trace 1. trigger coil 2. magnetic reed switch at dead center. What I found was the motor is powered on approach when the...
... input of energy. "If one is clever and gets back to absolute, simple fundamentals, it may be possible Dorro, you bet, And there is not a much simpler...
Dave, How about this, is it any more simple? http://groups.yahoo.com/group/Bedini_SG/files/joe/bediniworks.jpg ... I guess this also goes with the Attract and...
... <nebollinger@v...> wrote: "So take the same seneraio but switch to repel and the first repel will come just after dead center when the trigger generates v...
I still think this type of design is the direction to look towards.. Most designs can make a rotor travel almost 360 degrees under magnet assistance except for...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
