... longer letting the energizer swing into the hard on/off setup that it naturally will find on its own. Thus loading down the rotor reduces the "OU"...
Gene and all. I Agree with Gene. My own experiments have confirmed this. Any machanical resistance added to the rotor reduces charging performance and...
Hi Lee, I found one thing to be different than you noted below... when I added the fan, the current draw decreased some... Did you really see the current draw...
On Wed, 01 Feb 2006 22:04:13 +0000 ... Which means less rpms due to the load and the transistor is only turned on for the time that the trigger coil is induced...
... wrote: If the trigger was cam/dwell timed then the duty cycle would be the same with the load. I think you are likely correct, but could you explain the...
On Thu, 02 Feb 2006 00:27:31 +0000 ... The cam in the auto distributor opens at the same degrees everytime and stays open for the same degrees every time -...
Gene, Norman and all. I feel I must explain myself. I don�t wish to cause any confusion on this matter. My findings were observed while investigating the ...
Norman and all I tried advancing and retarding the trigger circuit timing recently. With the larger magnets on my rotor my base resistance was running towards...
Hi team, Running two in series 24.84 into 12.37 two in parallel. After settling out overnight I have 24.70 left on driving side and 12.46 on the parallel...
Ah gotcha Lee. Yeah my measurements were in only adding the fan to the shaft. I didn't change any other aspects... this makes sense then. :) Gene ... From:...
... Jack, I've been trying to recall, but can't. Do you remember the old wind power generating systems they used to have on farms years back. Did they have...
I think the Bedini oscillator is a wonderful device. When I posted the idea of 10 mags and 11 coils, I was thinking of smoothing things out. I wasn't in search...
... When I posted the idea of 10 mags and 11 coils, I was thinking of smoothing things out. I wasn't in search of torque... I was thinking of many small pulses...
... And also do you recall if these batteries had very high internal impedance? Jack, I found some references to the old glass case batteries they used in wind...
Dave: John has alluded to building his own batts,I dont think he has but anyone could do it.I have been thinking about it.--jw ... And also do you recall if...
New OU experimenter: You are very lucky to have started your research now. We have gone through a very slow learning curve. John, I'm afraid, just can't give...
Jack, What are you up to? Haven't heard much on your motor. You have to hang in there. You learn more by experimenting than you do by listening to engineers...
Hello all, So, if I read this correctly, there is NO ONE who has managed to replicate the "one battery charging 4" scenario? When I read 1:1 in the response...
... replicate the "one battery charging 4" scenario? When I read 1:1 in the response below, does this mean that the farthest anyone has gone has been to charge...
Norman, Given your statement below its pretty simple to convert this to a static mechanism... to be able to maintain cam/dwell setups... All you're saying, I...
... <goodman_luther@...> wrote: So, if I read this correctly, there is NO ONE who has managed to replicate the "one battery charging 4" scenario? Luther, As an...
... In Bedini_SG@yahoogroups.com, Luther Goodman ... to ... Luther, As an afterthought perhaps the question needs answering: There you go Luther, The answer is...
I have not found any battery charger capability yet. I have gone back to my original hand wound coil but this time I separated the trigger coil. The original...
... Hi Luther, I think your question is fair. I have gone at this a long time, and still not found the 4 to 1 ratio. Those that say it can be achieved may be...
Before you throw in the towel, I would personaly ask you wait just a bit more. I am playing with a concept rotor that may well help out in the quest here. I...
Thaelin, Just passing on the moderator job to a someone half way along. That way they should be a bit closer to the new experimenters and their questions. Not...
I'm not advising you to trig the energizer that way. It's supposed to trig according to the core's state. Putting it aside will need a lot of precision and you...
I have the rotor running quite well with the separate trigger and might even try to make it adjustable to experiment with variable timing. Monsieur Bonheur...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
