Hi DMR, It occured to me that you might or rather must be using small guage wire... and perhaps thats why you aren't seeing the full voltage come thru the coil...
Hi DMR, Gotcha... Are you just running the SSG setup? Meaning a single transistor on the power/trigger with the diode off the collector to the charge battery?...
Hi Gene, Swg18 ish, I use the primary windings of microwave transformers, so for their length with an iron core they could handle 240v ac of high current (be...
Hi Gene, ... transistor on the power/trigger with the diode off the collector to the charge battery? Yes, exactly. ... really low if you are running at 9v or...
Hi Dave, Sorry, I meant that the negative resistor effect only seems to AFFECT the current and not the voltage readings. I agree that there should be minimal...
Hi Gene, Yer, I understand what you're saying. I've been meaning to get a hydrometer recently. Measuring voltage can be deceiving or misleading as to what's...
Does any or all of the wiring between the recovery winding and battery via any cap pulser need to be heavy duty thick, as recommended for the battery charging...
Hi Clive, I'd think it be the inverse of what you are thinking with the large wire... since the cap does the conversion back to positive energy past the charge...
Clive, Gene, My next upgrade to my setup is to add bus-bars to both front and back ends of the system. I have made up several short 15mm diameter copper tube...
Thanks for your thoughts Gene. Working with a 100uS pulse into a battery with a resistance of .0023 ohms as an example, using T=CR we get a cap value of approx...
Hi Clive, I've not been able to get the 555 timer to pulse at the 100uS pulse rate as it seems to be to fast for the 555 IC to hit accurately. (thats with a...
Hi Gene The problem is the duty cycle for a 555 timer has to be between 55% to 95% which clearly does not allow a 100uS to 2S ratio. Somewhere I have got a...
Its been awhile, but I have been thinking of trying a multi-coil version of the SG. How are you guys connecting the outputs of the multiple coils together? If...
Hello Jim: This is where JB said timing is vary impotent All the coils must match and all the wireing has to be the same.the cables going to to the batts the...
Dave: When this site was just starting I encureged+ evryone to to use large wires I use #4 welding to the batt.and use big stuff all over for the same reason...
I have just carried out my first test run using the mechanical rotary pulser shown in my photo file. The set up was as follows: - I used my 7 inch / 6 mag...
Hi Clive, Sorry man, I guess I wasn't clear. I know how to tweak the timer setup to get the 1-99% duty cycles and have done this when I setup my pulser with...
Hi Clive, Another idea would be to swap the power and recovery windings as they are and see how that compares in the stators output to the charge cap. That...
Hi Gene Sorry I misunderstood your problem. I can now see what your getting at and this is a problem I've had when trying to outpulse in this order of time....
Hi Gene I've copied over part of my post from the SG2 forum below as this details the recovery winding performance of my new coil. I have no problem in getting...
A couple of mistakes crept into my report below. The ref to 3 x 22,000uF caps in series should have read a total of 7,333uF, not 30,000uF. The voltage rise...
Thanks Alex, this looks good. Do you intend to try it with a Bedini SG energiser? I'll give this a try, as a more elegant alternative to my mechanical rotary...
Alex The SG in itself is not an over unity device. However, my understanding is that the cap pulser used in conjunction with the SG is intended to take us over...
SUMMARY OF RELEVANT FACTS ========================= POSTED BY JOHN BEDINI ===================== Postings made to the Bedini_SG list. Compiled by Dave Michael...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
