Eric, I didn't see a reply to your questions, so I'll give it a shot. You may have gotten private messages, I don't know. The whole idea of the groups is to...
5756
farmnsouthtx
Jan 14, 2007 6:03 pm
This is my setup. If any questions please ask. Thanks, Chad...
5757
kenny_ppm
Jan 15, 2007 3:09 pm
Does anyone know a good source for pre-twisted litz wire? MWSwire quoted a lot of money per foot. Any others out there? ken...
5758
Dan Breeden
wd_breeden
Jan 15, 2007 3:41 pm
I've been buying Litz wire on E-bay. I paid $80 for a 7 lb roll and then a week later I paid $23 for a 7.5 lb roll.. Same stuff. I also see pure silver Litz on...
5759
kenny_ppm
Jan 15, 2007 9:11 pm
Dan, thats a good idea. Let me know if the seller you buy from has an online store with more than just a few items please. Because I just checked ebay and the...
5760
Dan Breeden
wd_breeden
Jan 16, 2007 4:54 am
$33 a pound!! I should go into business. There is a local place that sells for $3.50 lb Here's the store that I bought from; ...
5761
kenny_ppm
Jan 16, 2007 7:22 am
thanks! ... that sells for $3.50 lb ... more ... just ... and...
5762
kenny_ppm
Jan 16, 2007 7:26 am
Oh, does anyone which is better for the energizer coil? Larger diameter wire (lower gauge) or smaller diameter wire (higher gauge) for getting the pulses? ? ...
5763
Jack R Welch
jack82721
Jan 16, 2007 8:22 am
Hello Kenny:With the price of copper as high as it is! Get enough to make your first coil abt 200ft and make it #20ga that way you can recycle it later on.Dont...
5764
Glenn Lee
glennxlee
Jan 16, 2007 12:23 pm
John says to make all three wires of the same gauge ... From: kenny_ppm <debtelimination2@...> To: Bedini_SG@yahoogroups.com Sent: Tuesday, January 16,...
5765
kenny_ppm
Jan 16, 2007 12:49 pm
Thank you Jack, I have already done as you mentioned with my solid state energizer and I see it is working! With that proof, I am now on to building a huge...
5766
tom_chlds
Jan 16, 2007 9:40 pm
Hello all, Tom Childs from oregon here...... I am really at the front of this, I am still getting my components together, the neon lamps are all I am waiting...
5767
kenny_ppm
Jan 16, 2007 11:54 pm
welcome 1. the grain is NOT that important here: just use welding rod , you'll be fine. The oscillation pulse of the coil does most of the magic. 2. 4 is...
5768
Donald Haas
brodonhaas
Jan 17, 2007 12:07 am
HI everyone, What will do the job on a basic level for our machines? For example: 30 mhz, dual trace analog. No experience with scopes, need to know what specs...
5769
cffltrc
Jan 17, 2007 2:05 am
Correct me if I am wrong, but I think what John means by large coil is more strands and heavier gauge wire - not more turns of wire. In my latest multi-strand...
5771
Danny B
wd_breeden
Jan 17, 2007 2:40 am
Rob, John was very clear about wire length. If you take the time to read the old posts. #1377, he said not to go over 100 ft. of # 18 # 18 is what is being...
5772
cffltrc
Jan 17, 2007 3:42 am
... Thank you Dan That was exactly the point I was trying to make. RobC...
5773
joe_1001101
Jan 17, 2007 4:31 am
Hi Tom, ... I used resistors, keeping the signal around 1v (as the audio mixer likes) before it was fed it into the computer running protools LE v5 using an...
5774
joe_1001101
Jan 17, 2007 5:33 am
wants that is. ... Anyone want to change the group photo? Send new designs to me...SMALL file size. Thanks, Joe...
5775
chad farmer
farmnsouthtx
Jan 17, 2007 6:44 am
Hello Tom, 1- often coils use grain aligned steel for their core, will this ... The welding rods work. My coil only has 160ft. #20 x 3 strands litz together by...
5776
kenny_ppm
Jan 17, 2007 3:00 pm
I am going to have a very large battery bank soon. After reading a bunch of posts and ppl's input, I think the best configuration in my case should be large...
5777
Dan Breeden
wd_breeden
Jan 17, 2007 4:45 pm
Kenny, very large is a relative term. If you have to buy new batts, you need to look at HUP batteries. They seem to be both cheap and the best. You don't want...
5778
kenny_ppm
Jan 17, 2007 10:06 pm
I was thinking forklift batteries. But I will check out the HUP batteries you mention. Do you have any experience with the HUP type? Yes, I am going to charge...
5779
tom_chlds
Jan 17, 2007 10:22 pm
- Joe, you said resistors, are you just tapping into both sides of the coil, then slapping a bunch of resistors in series n the + side of thwe coil to get 1...
5781
Danny B
wd_breeden
Jan 18, 2007 2:27 am
Kenny, If you read the HUP site, they mention some of the drawbacks of forklift batts. They mention that their batts can go to 50% where the forklift batts can...
5782
joe_1001101
Jan 18, 2007 2:29 am
Tom, Just looked at the device. It was left with the led in place across the coil with that 330 ohm resistor JB mentioned in his led test. Looks like I added...
5783
kenny_ppm
Jan 18, 2007 6:17 am
Although that is more than a "used" forklift battery, the HUP is of interest to me. I like the stackable, cells, idea. I'll keep it in mind, thanks! ... where ...
5784
kenny_ppm
Jan 18, 2007 6:21 am
Yes, I will find a happy medium for my coil. with all the input information. The final turns ratio will be decided more by a lb. per coil for me. I have...
5785
recordingstudio@...
tom_chlds
Jan 18, 2007 4:34 pm
thanks joe! ... From: "joe_1001101" <acg_1001@...> Tom, Just looked at the device. It was left with the led in place across the coil with that 330 ohm...
5786
kenny_ppm
Jan 19, 2007 6:12 am
If, and I really stress the IF, this is true, I will get one of these for batterys and test the new coils. ...
