Hello, stay below .8 ohms per winding, try to match resistance in each winding. Also use L60 Lincoln welding rods for the core. Your transistor is toast so put...
Hi, How do I stay below .8 ohms per winding? My current coil measurement at AWG#20 is at 2.9 ohms and the AWG#21 at 2.4 ohms. Do I reduce the windings to...
Hi, Thanks for the pointers. I'm going to start/rewire the entire circuit again and this time, going through very slowly....:-) I'd just bought a couple of...
Hi guys, I'd finally got the rotor to spin AT LAST! Never have I been happier to see it spinning! The transistor ran cold! Thanks guys.... your pointers did...
Sanmankl try going to ONSEMI.COM a lot of us buy or get samples from them all you pay is shipping thanks kevin ... From: sanmankl <sanmankl@...> To:...
I am not sure what he meant regarding the " .8 ohms per winding ", (probably what it says, .8 ohms for each wind, not total coil resistance by any means) but...
Congratulations. ... From: sanmankl To: Bedini_SG@yahoogroups.com Sent: Monday, April 02, 2007 9:49 AM Subject: [Bedini_SG] Working: was ssg circuit please...
If you want to make sure your coil is wired up with the right polarity, do a little test. Put a magnet on the top of your coil with the north pole facing down...
Nick, sanmankl, 2boxers, The strand resistance depends on the transistor used for a Given size coil, smaller setups using smaller ga wire and 2n3055's or...
Hi Sanmankl AWG 20 98 feet/ohm Do I reduce the windings to achieve .8 ohm? (Stupid question but thought I want to confirm this.)Yes you have to reduce the...
Good description. I would just add this to it. a small pulse is used to escape from the magnet to core attract back and then the return on that investment is...
Hi Miki, Thanks for your kind thoughts. My coil is more than 300 feet and I got something in the region of about 450 turns. I did managed to get my rotor...
Hi Sanmankl The typical front to back efficiency of the SSG energiser is around 50%, so your 0.2A / 0.1A is about normal as indicated by a DMM or analogue...
Hi Clive, Thanks for telling me. Saves me from beating my head thinking about my setup efficiency. So, what kind of gain do we actually find from charged...
Hi all, So....different school of thoughts about impedence matching (0.8 ohm) and inductance? I'd got 2 identical coils. Both of them are AWG#20/#21 single...
Hi, I think this is a great idea and worth a go. Saves a lot of sore thumb/fingers coiling it manually. I would love to get one too but the shipping cost will...
The reason for a bifilar wound coil is coupling and impedance matching. You won't get that with those demo coils. Winding a coil doesn't take long, especially...
Sanmankl If you have so mutch time you can do what you want but I wrote you minimum 75 feet.AWG 18 5 litzed wire max 100 feet. You can build 150 feet for...
Hi Atlantis, Please don't take offence about me questioning you about this. I'm in the very steep of learning process (and yes, I do have time; I'd only sleep...
Hi Sanmankl I have PM'd you on this. Regards Clive ... but ... around ... and ... current ... about ... is ... <atlantisrd2005@> ... welding ... rod. ... one. ...
Hi Atlantis, No offence meant and none taken....:-) We are all in this together....:-) Thanks for your tip. sanmankl ... in ... only ... wire ... rotor ... ...
Thanks for the report Miki, Sorry for the late reply:) Joe ... load ... all ... project. ... probably ... negative ... was ... breakthrough ... will ... ...
Hi all, Been a while since I have been in here. Busy with projects outside and working closely with ************* on some projects. Bob Teal had the most...
Hello Group, I have uploaded a useful utility to the files area called e-mail stripper. It removes the excess >>>>>>>>>>>>> from any text file you put into it....
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
