CANbus : Messages : 4527-4556 of 7415

Messages: Simplify \| Expand (Group by Topic)		Author	Sort by Date

4527	Hello. Are there any ready implementations regarding OSEK VDX standard? (Transportprotocols for diagnosis vw, mercedes, ... And interaction between ecu´s) ...	friedo friedo72@...	Mar 1, 2005 5:18 pm
4528	Hi Friedo, have a look at http://www.realtime-os.info/osekvdx.html Best Regards Juergen ... Juergen Klueser Global Product Line Manager PON Open Networking...	Klüser, Jürgen Juergen.Klueser@...	Mar 3, 2005 9:52 am
4529	We use the SJA1000 in PeliCAN mode at 100kbit/s and we experience a strange situation on where the SJA1000 interrupt register reads 0xFF. Under normal...	Dan GÃ¸ran Lunde Dan.Goran.Lunde@...	Mar 3, 2005 6:09 pm
4530	... My guess is that you don't read the IRQ register but another unmapped address instead. Cheers /Ake -- ... Ake Hedman (YAP - Yet Another Programmer) ...	Ake Hedman akhe@...	Mar 3, 2005 6:43 pm
4531	Typo: We are pretty sure that all the interrupts did not occur at once. Under normal circumstances things are working and we read the interrupt register as...	Dan Gøran Lunde Dan.Goran.Lunde@...	Mar 4, 2005 11:11 am
4532	Excellent and informative article, Thilo! Dr K H Tang Embedded System, CAN, DeviceNet Controller Area Network Solutions (M) Sdn Bhd http://www.cans.com.my ...	Dr K H Tang xiong@...	Mar 7, 2005 3:19 am
4533	Hi Fabio Parodi, We are doing the same for our clients. DeviceNet is indeed a reference protocol for a good communication protocol design, despite its...	Dr K H Tang xiong@...	Mar 7, 2005 3:21 am
4534	Hello, does anyone out there have any audi canbus message id format that they would care to share here...or you can email me personally. I'm looking at the...	magic_man_two magic_man_two@...	Mar 11, 2005 7:31 pm
4535	Hallo all, I seem to be having a problem with ST10 269 Processor CAN Controller when I send two CAN messages (both 8 bytes long at 500K Baud) at just 300...	Balakrishnan Muthukri... balakrishm@...	Mar 12, 2005 9:11 am
4536	The ST7F561 datasheet includes details of a corruption possible in the CAN receiver hardware. Make sure you are not in the process of receiving a message when...	Peter Wrigley pete@...	Mar 14, 2005 9:24 am
4537	Hello Peter and Bala, I would like to inform you that the CAN controllers (beCAN) of the ST72F561 and the (fullCAN) of the ST10269 are completely different...	Paul KINOWSKI paul.kinowski@...	Mar 15, 2005 11:02 am
4538	Hello, I am new to the CAN bus as it is being implemented for a solar car at the University of Kentucky, here is our website, if you want to check it out. ...	donnie@...	Mar 15, 2005 10:46 pm
4539	Donnie, I am certainly no CAN guru, as I'm just about to finish my first CAN design. Note: I used the Freescale/Motorola MC9S12 micro along with the TI CAN ...	Dave Havell david.havell@...	Mar 16, 2005 12:17 am
4540	Just my 2c: For a custom design, where all the nodes can use a protocol defined by you, you can draw most likely less advantage of the HLPs. (CanOpen,...	Bende Georg georg.bende@...	Mar 16, 2005 9:49 am
4541	... I may extend. Not only in the case you have to integrate other COTS products. Even with a custom design you have to consider a lot of things, including...	Heinz-Juergen Oertel oe@...	Mar 16, 2005 12:18 pm
4542	Donnie, Let me second some of what Dave has said: Cable length is a factor, more so at higher speeds. I don't remember what the "official" limitation is at...	Allen Pothoof apothoof@...	Mar 16, 2005 4:27 pm
4543	The main thing to realise about the termination is that it is primarily not there to do any impedence matching or similar (though of course it does this to an...	Charles Manning Charles.Manning@...	Mar 16, 2005 9:26 pm
4544	Hey, You do speak about "vehicle wiring that was basically shielded twisted-pair". Well, almost all wiring in vehicles I've seen was UNshielded twisted-pair". ...	Tekla Mortelmans tekla.mortelmans@...	Mar 17, 2005 10:28 am
4545	Dear all, I need the the F_CAN- and the PT_CAN-Identifier of the BMW (E60). Where can I get this data? Bye... ...	juergen darmstadt id_juergen@...	Mar 17, 2005 11:02 am
4546	Depends on the vehicle and the use: for "regular" passenger-type vehicles, you are undoubtedly correct. But, up until a couple years ago, most of my CAN...	Allen Pothoof apothoof@...	Mar 17, 2005 4:12 pm
4547	Thanks to everyone for your replies, you have been quite helpful. :-) CAT5 cable with DB9 connectors sounds pretty good to me for our solar car since CAT5...	donnie@...	Mar 17, 2005 4:37 pm
4548	... you are right, the Lawicel CAN232 is intended to be an PC (or whatever) RS232 interface to CAN. You need the opposite direction. May I suggest to have a...	Heinz-Juergen Oertel oe@...	Mar 17, 2005 5:32 pm
4549	Hi Donnie, You're correct about the CAN232 needing a bit of 'packaging' around your real RS232 data. That's because a stream of RS232 characters from a device...	John Dammeyer johnd@...	Mar 17, 2005 5:44 pm
4550	Hi, [snip] ... We are the maker of CAN232 and yes it must have a "master" talking to it from the RS232 side, this master can be a PC (though there are much...	Lars Wictorsson lars@...	Mar 17, 2005 6:24 pm
4551	I'm playing around with some EDS files lately. I have a warning in my current file I'm unable to get rid of. It says: 603_3150_51.eds(809) : warning 4: Access...	Bende Georg georg.bende@...	Mar 18, 2005 11:58 am
4552	Hi Georg, an application object (6040) has to mention if it can be mapped into a TPDO or RPDO. Simply saying RW does not make this clear enough, specifically...	KlÃ¼ser, JÃ¼rgen Juergen.Klueser@...	Mar 18, 2005 1:21 pm
4553	Hey, Someone asked me about KIBES in relation to CAN. Does anyone know something about this, because I don't. Any information or links are welcome because I...	Tekla Mortelmans tekla.mortelmans@...	Mar 18, 2005 2:19 pm
4554	Hi Tekla, this is a complete control system. For communication it uses/supports CAN. => ...	KlÃ¼ser, JÃ¼rgen Juergen.Klueser@...	Mar 18, 2005 3:34 pm
4555	Hi Telka, Check this out. http://www.siemensvdo.com/default.aspx?menu=kibes_main Cheers, Steve ... From: canlist-owner@... ...	Corrigan, Steve s-corrigan1@...	Mar 18, 2005 4:32 pm
4556	Donnie, there are several full blown motor controllers and servo amplifiers that talk CAN...err, CANOpen at least. Try AMC or ACTech maybe. On a related note...	Dave Havell david.havell@...	Mar 18, 2005 6:33 pm

Yahoo! Groups Tips

Did you know...

Messages

Yahoo! My Yahoo! Mail
	Sign In New User? Sign Up
		Tech - Groups - Help

Yahoo! Groups Tips

Did you know...

Best of Y! Groups

Messages