Does anyone know of a "standard" connector used for CAN, which provides locking action or some other positive retention mechanism (i.e., other than the...
Genedyne
genedyne@...
May 2, 2006 8:19 pm
5512
Robb, We use a standard RJ45 and it works great for us. But there is no CAN specific connector per se, so you really have lot's of options. If you're design...
Havell, David @ MPRI-...
David.Havell@...
May 2, 2006 8:55 pm
5513
Hi Rob, The M12 connector is very popular. Many "ruggedized" versions are available from companies like TURCK. Just do a web search. Cheers, Steve C. ...
Corrigan, Steve
s-corrigan1@...
May 2, 2006 9:31 pm
5514
Hello Yaniv, There are an abundance of inexpensive 120-ohm UTP cable providers on-line such as Newark -- newarkinone.com. Do a search. Here in the US (big...
Corrigan, Steve
s-corrigan1@...
May 2, 2006 9:40 pm
5515
Hello Try Deutsch. They make the diagnostic connectors for heavy duty truck and I have seen a three pin DT06-3S used in a CAN system. ...
Robert Boys
RBoys@...
May 3, 2006 12:50 am
5516
Thanks for the pointer, Robert. I like the bladder sealing and quick disconnect in this series of connectors. I'm not sure if connector imepdance mismatch is...
Genedyne
genedyne@...
May 3, 2006 3:09 pm
5517
Thanks for the pointer, Steve. Do you have any idea if connector impedance mismatch is a concern at higher rates? Unfortunately, the Turck website rates about...
Genedyne
genedyne@...
May 3, 2006 3:12 pm
5518
That's brilliant! After getting a bit sick of poking around for information, I downloaded all 8MB of the product catalogue (from the .co.uk website). It's 600 ...
Peter Wrigley
pete@...
May 3, 2006 3:36 pm
5519
Hi Rob, I sure sympathize with your website woes. Sites like Digikey's are really refreshing. I have not seen any problems develop over a small impedance...
Corrigan, Steve
s-corrigan1@...
May 3, 2006 4:40 pm
5520
Can anyone help clarify the CAN fault confinement procedure for me? AIUI we start off in Error Active mode and if either the TEC or REC counters exceed 127...
Offshore Systems (UK)...
bruce@...
May 3, 2006 5:52 pm
5521
Bruce, Normal data communication is possible in error-passive mode. However, I believe the error frames generated by a EP node is different. Your understanding...
Janakiraman, Hareesh
hareesh@...
May 3, 2006 7:50 pm
5522
Hi This connector was used by a big player in the J1939 market. I forgot exactly which one. They used this connector on one of their modules to connect to the...
Robert Boys
RBoys@...
May 3, 2006 9:35 pm
5523
Hi Steve, Thank you for your answer, I do not have an uncontrolled need to use the CAT5 ETH cabels :) and probably won't use them because I can find the proper...
Yaniv (sent by Nabble...
lists@...
May 3, 2006 10:30 pm
5524
Yaniv, I think I have missed some of this conversation, so this comment may be completely useless to you. But here goes anyway... I use RJ45 connectors with...
Havell, David @ MPRI-...
David.Havell@...
May 3, 2006 11:04 pm
5525
Hello Yaniv, Don't know of any off hand. Beldin cable has some good cable listed under keyword RS-485, which uses the same 120ohm cable. I'm using their ...
Corrigan, Steve
s-corrigan1@...
May 4, 2006 1:53 am
5526
Dave, Actually it is not useless at all :) Since I wanted to try RJ-45 connectors anyway I might just give it a try with an of-the-shelf ETH patch cable and...
Yaniv (sent by Nabble...
lists@...
May 4, 2006 1:54 am
5527
Hi, We are considering Molex Micro-Fit series connectors for high speed and industrial spec CAN bus in our system. Features are : 1. PCB retension- nails and...
Amey.Gambhir@...
May 4, 2006 3:27 am
5528
Talking about cable, we just did EMC burst tests, IEC 801-4. CE level is 1KV with the CAN cable in the capacitive clamp. Our results were, that the CAN...
Peter Lauer
plauer@...
May 4, 2006 3:38 am
5529
Hi Steve yes I realized that it's the same RS-485 cables... thank you for the advice! cheers Yaniv -- View this message in context:...
Yaniv (sent by Nabble...
lists@...
May 4, 2006 9:04 am
5530
Hi Peter, We have passed our products through the same tests recently with cables up to 5m long and had no problems with CAN. We run at 20 kbps, have shielded...
Fabrice Lucas
fabrice.lucas@...
May 4, 2006 12:29 pm
5531
Hi Bruce, This is my definition of the 3 error states; 1. Error Active In plain English "Error Active" indicates that the node is working correctly. Receive...
esd - Wilfred Voss
wilfred.voss@...
May 4, 2006 2:34 pm
5532
After visiting a few other connector sites with similar issues in search of other M12 offerings, I've decided to coin the word "wenema" (short for web-enema)...
Genedyne
genedyne@...
May 4, 2006 8:24 pm
5533
Hi Bruce, I have only small thing to add to this very good explenation: In "Error Active" mode CAN controller is allowed to transmit immediatly after the IFS...
Thilo Schumann
canlist@...
May 5, 2006 9:45 am
5534
Hi Bruce, because a missing Acknowledge is not regarded as a serious error, which means the Tx-Counter is not anymore incremented, when it is above 127. Such a...
Thilo Schumann
canlist@...
May 5, 2006 10:45 am
5535
I want to compile the can4linux-3.3.4 driver (kernel 2.4.27) with the Motorola ColdFire 5282. In which target I have to compile it? The supported target are:...
mjbataller (sent by N...
lists@...
May 5, 2006 11:18 am
5536
Hi Bruce, ... Yes, you should. All CAN-controllers I have seen, are able to provide interrupt requests when they change their operatinal mode between error...
Heikki Saha
heikki.saha@...
May 5, 2006 12:04 pm
5537
Thank you everybody who has responded to my question. From what I have learnt the bus off recovery procedure should be handled automatically by our Atmel...
Offshore Systems (UK)...
bruce@...
May 5, 2006 12:06 pm
5538
... Really? Heikki, read his question again please Heinz -- Archives and useful links: http://groups.yahoo.com/group/CANbus Subscribe and unsubscribe at...
Heinz-Juergen Oertel
oe@...
May 5, 2006 1:26 pm
5539
... Please use 3.4 I hope you have already knowledge on Makefiles - and CAN. Heinz...
Heinz-Juergen Oertel
oe@...
May 5, 2006 1:26 pm
5540
Thilo, Many many thanks. You have explained what I am seeing and why it is that way. I really appreciate your response. Best regards Bruce ... From:...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
