CANbus : Messages : 5697-5726 of 7412

Messages: Simplify \| Expand (Group by Topic)		Author	Sort by Date

5697	Hello Khalid, Close. The data bytes for this instance consist of one, two byte instance of lamp status followed by one or more instances of a four byte DTC...	Jim DeVore jim@...	Jul 4, 2006 1:25 am
5698	Dear colleagues, I have been reading the J1939/73 spec, and trying to understand how exactly the DM1 messages are sent on a J1939 bus. I guess I am confused...	Khalid Ansari khalid.labview@...	Jul 4, 2006 1:36 am
5699	Hallo all, The UVNOM flag issue reported in TJA1041 which leads to STBN and EN not waking up the Transceiver (due to Undervoltage detection) calls for WAKE pin...	Balakrishnan Muthukri... balakrishm@...	Jul 6, 2006 11:18 am
5700	Hi I am having some difficulties to calculate the ideal slope control resistor for the TI 65HVD230 transceiver. The products we are producing are general ...	Thomas Jespersen (Log... tj@...	Jul 6, 2006 11:32 am
5701	Hi Thomas, Why do you feel that you need to incorporate slope control on the HVD230 at all? If you are setting up for many unknown applications, I recommend...	Corrigan, Steve s-corrigan1@...	Jul 6, 2006 2:40 pm
5702	Correct me if I am wrong. The Lamp Status is the Worst Status of the Red / Amber. Plus the other lamps as required. And the message must be sent as a...	Neil swjmnr@...	Jul 7, 2006 3:57 am
5703	Thank you very much for your reply Steve. I decided not to use slope control, but I will use a zero ohm resistor to gnd, which can be changed if needed in the...	Thomas Jespersen (Log... tj@...	Jul 7, 2006 8:55 am
5704	Hi Thomas, Good, you'll be fine. I'm not aware of any auto/truck using shielded cable, but it is quite common in industrial applications. Cheers, Steve C. ...	Corrigan, Steve s-corrigan1@...	Jul 7, 2006 1:14 pm
5705	The standard leaves arbitration of the lamp status within the DM1 to the device transmitting the DM1. The arbitration of the physical lamp status is performed...	Jim DeVore jim@...	Jul 7, 2006 5:31 pm
5706	Shielded cable was seen in American assembled, class 8 trucks five years ago, but it appears to be disappearing. Presumably due to cost -- unshielded is...	Jim DeVore jim@...	Jul 7, 2006 5:33 pm
5707	Hi I am using a PIC18F2480 an Hi-Tech C. Two Questions About the ECAN Module. I am tring to sleep whe the CAN Bus is disconnected and wakeup when it is...	Neil swjmnr@...	Jul 9, 2006 7:47 am
5708	Hi Neil, Regarding the failure to wake up from CAN bus activity, the only thing that comes to mind is the microchip requirement that the CAN module on the PIC...	Andy Campbell andy@...	Jul 10, 2006 10:39 am
5709	Hi all, I am implementing timeout supervision for RPDOs to detect missing RPDOs, and I intend to use the Event Timer (subindex 5 of the Comm Params). It seems...	Osmar Yang oy@...	Jul 10, 2006 8:13 pm
5710	My application is in a heavy duty on-road vehicle using a J1939 data bus, I am receiving and processing a broadcast (BAM) DM1 message from an engine controller...	Neil Frederickson neil@...	Jul 10, 2006 8:25 pm
5711	Thank You For Not Assuming. That was my problem. The PIC18F2480 Datasheet is not explict on the subject. I looked it up in the sheet (now that I know). Now...	Neil swjmnr@...	Jul 10, 2006 8:25 pm
5712	I think the practical limit would be defined by the number of DTC's present. Other devices, such as diagnostic tools, have limits, too. Even with 50 DTC's...	Jim DeVore jim@...	Jul 11, 2006 4:36 am
5713	Hello to all. I use the TI SN65HVD234D. It seems to work ok! Best Regards Mike ... -- Archives and useful links: http://groups.yahoo.com/group/CANbus Subscribe...	Mike S. powersurf@...	Jul 11, 2006 11:02 am
5714	hi If my Node is disconnected from the CAN bus will it get to the bus off state? I would assume this would cuase a buss off by TX errors. It seems to stop at...	Neil swjmnr@...	Jul 12, 2006 4:09 am
5715	It will only get passive errors if disconnected. Depending on the controller, these might be "not acknowledged" type errors. A CAN controller cannot completely...	Charles Manning Charles.Manning@...	Jul 12, 2006 5:32 am
5716	Interesting, but maybe bad news for me. My Node is a J1939 Battery. I send Messages out. No one talks to me. I need to sleep whwn the battery is pulled from...	Neil swjmnr@...	Jul 12, 2006 6:08 am
5717	Hello, I'm currently creating an application with the ISO 11783 standard. Now I'm working with the virtual terminal, which has some OEM software on it. But I...	reeva@...	Jul 12, 2006 8:11 am
5718	... Some CAN controllers have a very sophisticated interface to the error confinement rules inside. Look at the SJA1000 manual, it describes the "Error Code...	Heinz-Juergen Oertel oe@...	Jul 12, 2006 8:26 am
5719	Neil, Depending on your micro, you may or may not be able to test the ACK field in transmitted CAN messages. Again depending on your micro, there may also be a...	Peter Wrigley pete@...	Jul 12, 2006 8:30 am
5720	Hello Alexander, here's the answer of a colleague: The terminal will only accept CAN frames from your device if you are either an working set master or a...	Klüser, Jürgen Juergen.Klueser@...	Jul 12, 2006 1:36 pm
5721	Hello, I am new CAN bus. I can use CAN in legacy mode but I cannot achieve to use CAN in enhanced FIFO mode. When the can bus receives more than 2 messages I ...	hamid kutlu hamid.kutlu@...	Jul 12, 2006 1:41 pm
5722	Hello , I have made a little mistake in my code. It solved my problem. sorry for taking your time...	hamid kutlu hamid.kutlu@...	Jul 12, 2006 3:50 pm
5723	Jim, thanks for your insight on this. FYI, the ECM I am dealing with has 130 listed DTCs, have decided to limit the number of DTCs I handle within a given...	Neil Frederickson neil@...	Jul 12, 2006 7:21 pm
5724	Hello! Does no one talk to you, or is no one else on the bus? If you are sending out messages, I guess there is someone listening giving ACK signals (Otherwise...	Ursula.Kelling@...	Jul 13, 2006 2:34 am
5725	Hello! This feature is on all Infineon micros with CAN module, as well as on the Bosch IP modules, I am aware of. (Bosch supplies to many vendors their IP...	Ursula.Kelling@...	Jul 13, 2006 2:54 am
5726	Thanks Ursula, It's good to hear from you. I was wondering about this. Thanks, Steve C. ... From: canlist-owner@... ...	Corrigan, Steve s-corrigan1@...	Jul 13, 2006 5:54 am

Yahoo! Groups Tips

Did you know...

Messages

Yahoo! My Yahoo! Mail
	Sign In New User? Sign Up
		Tech - Groups - Help

Yahoo! Groups Tips

Did you know...

Best of Y! Groups

Messages