Hello group, we have an environment with mostly SJA1000 CAN controllers. But one component has PIC18F4480 controller. Sometimes we get bus errors when a SJA...
Bayerlein, Helmut
helmut.bayerlein@...
Oct 4, 2006 1:10 pm
5835
Hi Helmut, None that I've heard off, but then there is probably more of a difference between your two nodes than just the SJA and the PIC. Do you have an...
Andy Campbell
andy@...
Oct 4, 2006 2:20 pm
5836
Hello, I want to buy j1939 source code implementation for embedded system. The implementation should read/send j1939 messages (decode/encode those messages)...
ami
amihud.bruchim@...
Oct 5, 2006 12:22 pm
5837
Andy, thanks for your hints. It seems to be a problem with the oszillator (was 16MHz ceramic resonator) and propagation delay of opto couplers to the bus...
Bayerlein, Helmut
helmut.bayerlein@...
Oct 5, 2006 4:31 pm
5838
hello it was my problem when i started also but i am using a different microcontroller.but you will find very good resorces to give you a start at...
m.ali hussein
nourequip@...
Oct 8, 2006 2:50 am
5839
Hello, I'm loooking for free j1939 demo or simulator Thank you -- View this message in context:...
ami
amihud.bruchim@...
Oct 8, 2006 2:02 pm
5840
Hi ami Have a look here: http://rec.planetaclix.pt/j1939/ http://rec.planetaclix.pt/j1939/ Chapters 4, 5 and 6 deal with J1939 simulators. Regards, Rec -- View...
recursos
recursos.pt@...
Oct 9, 2006 6:17 pm
5841
Hello to everyone. I am working on a project and I use the MCP2510 chip to communicate through CAN Bus, but I have problem with the SPI communication (I try to...
Labropoulos Anastasios
tasos81@...
Oct 10, 2006 5:24 pm
5842
Hi, Make sure you have SI and SO correctly connected. It's easy to get confused and accidentally connect them wrong. Master in Slave Out (MISO) from the ...
John Dammeyer
johnd@...
Oct 10, 2006 6:22 pm
5843
Mr John Dammeyer thaks you for your reply. The SI and SO pins are correctly connected but i don't know if is necessary to put in any resostor. I have connected...
Labropoulos Anastasios
tasos81@...
Oct 11, 2006 8:56 pm
5844
Hi, I've sent some schematics and source code to your personal email address. It shows a PIC based SPI to MCP2510 connection and some routines that display the...
John Dammeyer
johnd@...
Oct 11, 2006 9:46 pm
5845
Hello experts, I have a small problem with our device. We have an RS232 & CAN driver on the same communication line, normally the RS232 is shut down. Our...
Bende Georg
georg.bende@...
Oct 12, 2006 4:50 pm
5846
Hi Experts, If some of you has the datasheet in the $subject, can please someone look up, whether there is any specification for the maximum unterminated stub...
Bende Georg
georg.bende@...
Oct 12, 2006 5:32 pm
5847
Hello, CiA DR 303-1 gives theorethical equations and SAE J2284-250 and -500 give more practical listings for supported topology deviations and node counts per...
heikki.saha@...
Oct 23, 2006 3:08 pm
5848
http://www.canexperts.de/software/can4linux.3.4.5.tgz beta version with support for SMP machines like Intel Core Duo and for 64 bit processors. Please test ...
Heinz-Juergen Oertel
oe@...
Oct 23, 2006 3:53 pm
5849
Hello everyone, Does somebody knows if I need special hardware to use MilCAN or can I just have any drivers or software to adapt it. We are developing a C...
elaacc
elaacc@...
Nov 3, 2006 9:55 am
5850
... Alberto, MilCAN is a software-based higher layer protocol that uses CAN and does not need any special hardware. It is an open protocol (which you can ...
Periklis Charchalakis
P.Charchalakis@...
Nov 3, 2006 12:13 pm
5851
Hi Alberto, Dr Charchalakis is correct about stopping a message. If possible select a CAN controller which can be programmed to send only once and not...
John Dammeyer
johnd@...
Nov 3, 2006 7:16 pm
5852
I was asked offline which TI part this was. SN65HVD1050 transceiver. You can read about it at www.ti.com/aaj John Dammeyer Wireless CAN with the CANRF module...
John Dammeyer
johnd@...
Nov 3, 2006 8:36 pm
5853
Hi, I want to know What are the Layers that CCP ( Can Calibration Protocol ) is involved with? Is it just the data that is transported in can messages (to...
ami
amihud.bruchim@...
Nov 5, 2006 9:51 am
5854
Hi John, We are facing a similar issue with the 800 series from Freescale. What tend (not impelented yet) to sense the TEC and in cases that this counter rises...
Moshe Barazani
mbarazani@...
Nov 5, 2006 10:43 am
5855
Hi Moshe, Yes. It does contradict CAN! But then so what? It's only an issue if Commercial Off The Shelf (COTS) devices need to be used with just different ...
John Dammeyer
johnd@...
Nov 5, 2006 8:16 pm
5856
I'm currently trying to qualify the CC770 as a replacement for our 82527 applications. I feel I am configuring the CC770 correctly, have reviewed the Intel...
Dan.Rohr@...
Nov 6, 2006 4:46 pm
5857
Hello I need document about Controller Area Network(CAN) being used in Textile Industry Best Regards -- Archives and useful links:...
ozlemkacar2001
ozlemkacar2001@...
Nov 6, 2006 4:47 pm
5858
CiA DSP-414 is the CANOpen standard for weaving machines, if you are looking for standards. BR, Georg Bende...
Bende Georg
georg.bende@...
Nov 6, 2006 5:39 pm
5859
Yes, daisy-chaining is a very comfortable way of ID assignment, we have an implementation as an extension of the LSS services and works well. Would be nice if...
Bende Georg
georg.bende@...
Nov 6, 2006 5:50 pm
5860
... -- Archives and useful links: http://groups.yahoo.com/group/CANbus Subscribe and unsubscribe at www.vector-informatik.com/canlist/ Report any problems to...
d_rohr
dan.rohr@...
Nov 6, 2006 6:00 pm
5861
Hello I need document about Controller Area Network(CAN) being used in Textile Industry Best Regards ...
özlem kacar
ozlemkacar2001@...
Nov 6, 2006 6:10 pm
5862
Hello everyone, The latest issue of Circuit Cellar Magazine, issue 196 Nov. 2006 (www.circuitcellar.com) has an interesting article by Eric Gagnon for an RS232...
John Dammeyer
johnd@...
Nov 6, 2006 6:14 pm
5863
Hi there! I would like to know if it's somehow easy to monitor a CAN bus in my vehicle (Fiat Palio) to read simple things like the speed, rotation, fuel. Are...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
