Hello everyone, Does somebody knows if I need special hardware to use MilCAN or can I just have any drivers or software to adapt it. We are developing a C...
elaacc
elaacc@...
Nov 3, 2006 9:55 am
5850
... Alberto, MilCAN is a software-based higher layer protocol that uses CAN and does not need any special hardware. It is an open protocol (which you can ...
Periklis Charchalakis
P.Charchalakis@...
Nov 3, 2006 12:13 pm
5851
Hi Alberto, Dr Charchalakis is correct about stopping a message. If possible select a CAN controller which can be programmed to send only once and not...
John Dammeyer
johnd@...
Nov 3, 2006 7:16 pm
5852
I was asked offline which TI part this was. SN65HVD1050 transceiver. You can read about it at www.ti.com/aaj John Dammeyer Wireless CAN with the CANRF module...
John Dammeyer
johnd@...
Nov 3, 2006 8:36 pm
5853
Hi, I want to know What are the Layers that CCP ( Can Calibration Protocol ) is involved with? Is it just the data that is transported in can messages (to...
ami
amihud.bruchim@...
Nov 5, 2006 9:51 am
5854
Hi John, We are facing a similar issue with the 800 series from Freescale. What tend (not impelented yet) to sense the TEC and in cases that this counter rises...
Moshe Barazani
mbarazani@...
Nov 5, 2006 10:43 am
5855
Hi Moshe, Yes. It does contradict CAN! But then so what? It's only an issue if Commercial Off The Shelf (COTS) devices need to be used with just different ...
John Dammeyer
johnd@...
Nov 5, 2006 8:16 pm
5856
I'm currently trying to qualify the CC770 as a replacement for our 82527 applications. I feel I am configuring the CC770 correctly, have reviewed the Intel...
Dan.Rohr@...
Nov 6, 2006 4:46 pm
5857
Hello I need document about Controller Area Network(CAN) being used in Textile Industry Best Regards -- Archives and useful links:...
ozlemkacar2001
ozlemkacar2001@...
Nov 6, 2006 4:47 pm
5858
CiA DSP-414 is the CANOpen standard for weaving machines, if you are looking for standards. BR, Georg Bende...
Bende Georg
georg.bende@...
Nov 6, 2006 5:39 pm
5859
Yes, daisy-chaining is a very comfortable way of ID assignment, we have an implementation as an extension of the LSS services and works well. Would be nice if...
Bende Georg
georg.bende@...
Nov 6, 2006 5:50 pm
5860
... -- Archives and useful links: http://groups.yahoo.com/group/CANbus Subscribe and unsubscribe at www.vector-informatik.com/canlist/ Report any problems to...
d_rohr
dan.rohr@...
Nov 6, 2006 6:00 pm
5861
Hello I need document about Controller Area Network(CAN) being used in Textile Industry Best Regards ...
özlem kacar
ozlemkacar2001@...
Nov 6, 2006 6:10 pm
5862
Hello everyone, The latest issue of Circuit Cellar Magazine, issue 196 Nov. 2006 (www.circuitcellar.com) has an interesting article by Eric Gagnon for an RS232...
John Dammeyer
johnd@...
Nov 6, 2006 6:14 pm
5863
Hi there! I would like to know if it's somehow easy to monitor a CAN bus in my vehicle (Fiat Palio) to read simple things like the speed, rotation, fuel. Are...
Rafael D'Angelo Machado
Rafael.Machado@...
Nov 6, 2006 7:17 pm
5864
... Georg, if we see enough interest in the market in a daisy chain solution, we will provide a standard. At the time LSS was specified the requirements have...
Heinz-Juergen Oertel
oe@...
Nov 6, 2006 8:25 pm
5865
Hi John, What you describe is already done in many, what we call in the control automation business, a modular I/O device. In this case the nodes are I/O...
rene.heijma@...
Nov 7, 2006 9:11 am
5866
Heinz, <snip> ... </snip> I know only roughly how it works, please correct me if I'm wrong. It is good to get your network up and running, but you don't get...
Bende Georg
georg.bende@...
Nov 7, 2006 10:30 am
5867
Hello, I don't have any documentatin about CAN in textile industry. However I have been developing our new generation genset control equipment which gets the...
hamid kutlu
hamid.kutlu@...
Nov 7, 2006 3:21 pm
5868
I think I have finally figured out where I'm suppose to post new messages. Not sure if I have, but I apologize if I have been generating previous emails on...
d_rohr
dan.rohr@...
Nov 7, 2006 4:48 pm
5869
Hi Guys I have J1939 Stack with me i have written by my own and i have tested in my Lab its working fine. If anybody is interested to have this J1939 Protocol...
Rakesh Krishnan
rakesh_kochi@...
Nov 7, 2006 5:11 pm
5870
Hello İs there anyone who has files CiA DSP 414-1 V1.0 ... 1: General Definitions and CiA DSP 414-2 V1.0 : CANopen Device Profiles for Weaving Machines -...
özlem kacar
ozlemkacar2001@...
Nov 8, 2006 12:03 am
5871
Hi Dan, ... we have already done these tests and it works in our application. Maybe you have to specify in more detail what the problems are and what your ...
Torsten Krahl
krahl@...
Nov 8, 2006 9:00 am
5872
... That is correct ... Creating and maintaining of a standard is always a lot of work. Your help and the help of others is required. I can discuss this in...
Heinz-Juergen Oertel
oe@...
Nov 8, 2006 9:06 am
5873
... The above mentioned documents are in the state "for CiA members only". If it is for your home work, your school has to be a member of CAN in Automation....
Heinz-Juergen Oertel
oe@...
Nov 8, 2006 9:06 am
5874
Hello, Draft standards of CiA are free for everyone. The 414 ist in a DS Proposal state, which is free for members only. You can buy it at CiA:...
Klüser, Jürgen
Juergen.Klueser@...
Nov 8, 2006 9:11 am
5875
... Hello Jürgen, I'm not sure if you are right: Read at:http://www.can-cia.org/cia/standard.html ... Starting January 2005, CiA provides draft standard...
Heinz-Juergen Oertel
oe@...
Nov 8, 2006 2:54 pm
5876
It's good to hear the CC770 is working for you, that is encouraging. Some additional information is as follows. THANKS!! I have several applications for the...
Dan.Rohr@...
Nov 8, 2006 6:37 pm
5877
Hello, Would anyone mind to explain to a newbie how to get access to CAN automotive variables like speed, rotation, motor temperature, etc, using a CAN-enabled...
Rafael D'Angelo Machado
Rafael.Machado@...
Nov 9, 2006 5:49 pm
5878
Hi, I have designed glass touch switches and would like to connect them to CANBUS (in the first phase for automation system from Cybrotech and in second ...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
