Hi, i am able to read and understand the contents of can frames received from trucks of certain brands(renault for instance), those are extended frames(29bit...
Selçuk Cihan
selcukcihan@...
Jul 2, 2008 10:06 am
6659
Hi, i am able to read and understand the contents of can frames received from trucks of certain brands(renault for instance), those are extended frames(29bit...
Selçuk Cihan
selcukcihan@...
Jul 2, 2008 10:06 am
6660
Is it a J1939 device? Many CAN Kingdom or DeviceNet devices use the 11 bit CAN frames. SAE J1939 didn't define many PGNs on the 11 bit frame, but you can still...
Funny NYPD
funnynypd@...
Jul 2, 2008 2:33 pm
6661
... Thanks for the response, My device can receive both can 2.0a and can 2.0b frames. The problem is that, axor gives me only 2.0a frames (standard frames,...
Selçuk Cihan
selcukcihan@...
Jul 2, 2008 2:55 pm
6662
Greeting, Selçuk, You better check with ISO standards such as ISO11898 etc. There are some European truck/diesel engines using ISO standards instead of SAE...
Funny NYPD
funnynypd@...
Jul 2, 2008 3:49 pm
6663
Hello Cihan, this is a proprietary protocol. You will not get information about it, except you have a contract with Daimler. For more information have a search...
Klüser, Jürgen
Juergen.Klueser@...
Jul 2, 2008 3:51 pm
6664
... Hi, thanks a lot NYPD and Jürgen. At least now i know where i stand. -- Archives and useful links: http://groups.yahoo.com/group/CANbus Subscribe and...
Selçuk Cihan
selcukcihan@...
Jul 2, 2008 4:33 pm
6665
Hi all, Hi all, I have send a link that explains my CAN circuitry. I am using a standard 11bit CAN identifier at 500kbaud. I hooked up my CANH and CANL pins on...
Ram
rams@...
Jul 7, 2008 5:50 pm
6666
Ram, Remove the CANalyzer device. Attach the two terminating resistors between CANH and CANL, then view the bus with the scope, not the CANalyzer. What do you...
Corrigan, Steve
s-corrigan1@...
Jul 7, 2008 10:03 pm
6667
Hi there folks - I just thought I'd check in on this topic again. I have an upcoming board that needs to be 12.5x34.5mm and have CAN connectivity. I'm praying...
Michael J. Noone
mnoone@...
Jul 8, 2008 4:34 pm
6668
Hi Steve, Thanks for your advice. I tried without CAnalyzer and the behaviour didn't change. The differential voltage drops from 3V to 0.5V with one 120ohm...
Ram
rams@...
Jul 8, 2008 4:35 pm
6669
Hi Michael, Maxim has one. Just keep it lightly loaded to keep heat down. The MAX3051. Cheers, Steve C. ... From: canlist-owner@......
Corrigan, Steve
s-corrigan1@...
Jul 8, 2008 5:38 pm
6670
Hi all, Internal termination resistor is provided in the circuit but i thought adding a external 120ohm resistor shouldn't make a big difference. Any help...
Ram
rams@...
Jul 8, 2008 6:46 pm
6671
Ram, What is the distance between the nodes? Steve ... From: canlist-owner@... [mailto:canlist-owner@...]...
Corrigan, Steve
s-corrigan1@...
Jul 8, 2008 7:38 pm
6672
Hi Steve, Just one node in the bus. My board is the source and i am monitoring it using CAnalyzer as other CAN node (<5m). Thanks Ram ... -- Archives and...
Ram
rams@...
Jul 8, 2008 8:21 pm
6673
Hi all, Can anyone please explain me why the vendor has the choke (M2022A from coilcraft) and other discrete components between the transceiver and external...
Ram
rams@...
Jul 8, 2008 9:56 pm
6674
Ram, I think that you may have another kind of problem. Again, what is the distance between the nodes. Does it vary widely with some close to gether in a...
Corrigan, Steve
s-corrigan1@...
Jul 9, 2008 5:36 pm
6675
This is a email re-send due to long delay from vector: Greeting, Ram, Do you have 60 nodes or just one nodes? I am bit confused here. Removing all de-coup cap,...
Funny NYPD
funnynypd@...
Jul 9, 2008 7:27 pm
6676
Hi It should be less than 5m. Just a straight connection between two nodes. One node is my board with the circuit i sent and the other is CAnalyzer just to...
Ram
rams@...
Jul 9, 2008 7:28 pm
6677
I just have one Node and CAnalyzer hooked up to that node to monitor the CAN messages. Initially it was working with all the transient suppression circuit but...
Ram
rams@...
Jul 9, 2008 9:03 pm
6678
Hi Ram, My explanation for the behaviour is that there's something wrong with your suppression circuit regardless of what you think you have schematic wise. ...
John Dammeyer
johnd@...
Jul 9, 2008 10:50 pm
6679
Hi all.. I have a requirement for sensor/control nodes that measure temperature, RH, and fan speed inside IT server racks. There can literally be hundreds of...
Doug Johnson
doug@...
Jul 10, 2008 4:33 pm
6680
Hi all.. I have a requirement for sensor/control nodes that measure temperature, RH, and fan speed inside IT server racks. There can literally be hundreds of...
Doug Johnson
dj41354@...
Jul 10, 2008 4:35 pm
6681
... CANOPEN might be the right way to go but also have a look at VSCP (http://www.vscp.org) that will handle such a thing easy. Cheers /Ake -- ... Ake Hedman...
YAP
x112358@...
Jul 10, 2008 10:06 pm
6682
Hi Doug, ... CANopen is a good choice for this kind of application. You should take a look at the CAN in Automation website http://www.can-cia.org. There you ...
Torsten Krahl
krahl@...
Jul 11, 2008 8:34 am
6683
The long waiting Au SAE J1939 simulator Gen II editions are now available. http://www.auelectronics.com/System-J1939Simulator.htm simplified user manual is...
Funny NYPD
funnynypd@...
Jul 13, 2008 4:03 am
6684
PLEASE, this is no advertising list. I think it understandable and accepted, if you give a plug to your products when it is appropriated to a question. BUT, it...
Thilo Schumann
canlist@...
Jul 14, 2008 1:19 pm
6685
Hello everyone, I am learning milcan protocol and new on milcan now ,and the posts here were helpful, but I still have some questions about milcan, could you...
wsp75302
wsp75302@...
Jul 14, 2008 5:06 pm
6686
Hi, It's been more than two years since I looked at the MilCAN spec so I don't know if I can answer your questions completely. Comments below. ... Our client...
John Dammeyer
johnd@...
Jul 14, 2008 5:58 pm
6687
Hello everybody, I am currently working on a project that involves using an ISO11992 bus and the only transceiver I can find is the B10011S from Atmel. Do any...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
