Hi all, I'm locking for the CAN Message Map of TRUCK DAF 105 have you this document ??? Thank for your answer. <<Immagine (Metafile)>> Ing. Paolo Castellano ...
DTP Paolo Castellano
paolo.castellano@...
Oct 2, 2008 8:57 am
6734
Hi, I'm designing a CAN module with built in CAN bus termination resistors. The question is, what power rating do the resistors need? 1W, 2W? Br, -- Bertil...
Bertil Bäck
bertil.back@...
Oct 6, 2008 8:39 am
6735
Hello Br, What needs to be accounted for in a worst-case event is the "short-circuit output current" of the transceivers being used. This current would be for...
Corrigan, Steve
s-corrigan1@...
Oct 6, 2008 2:56 pm
6736
Hi Br, You should take in consideration a short circuit to the power train (14V or 27V?) to be sure that the resister want blow. The extreme but very rare case...
Martin Hollenweger
martin.hollenweger@...
Oct 6, 2008 6:19 pm
6737
Hi, Does anybody know the actuator number for the Panel LED on the HVAC module in the 2008 Chrysler/Dodge vehicles. I have found them for every other LED and...
Brian Edwards
b.edwards@...
Oct 6, 2008 8:38 pm
6738
Brian, I'm not an OBD expert, and I'm not even sure this is an OBD question, but I suspect you'll need to be even more specific. Chrysler sources climate...
Allen Pothoof
apothoof@...
Oct 7, 2008 12:58 pm
6739
Hi Al, The Chrysler OBD (CAN diagnostic) port allows you to take control of all the different actuators in the vehicle through the OBD port. I am looking for...
Brian Edwards
b.edwards@...
Oct 7, 2008 1:14 pm
6740
Hi Gurus, I'm so happy I've found this forum. I've been working with CAN for a few years and now I'm facing an odd problem. I apologize for the length of this ...
JXLL
jxll29@...
Oct 7, 2008 4:03 pm
6741
What's the crystal type and accuracy? Funny N. Au Group Electronics, http://www.AuElectronics.com ... From: JXLL <jxll29@...> Subject: [CANLIST]...
Funny NYPD
funnynypd@...
Oct 7, 2008 5:22 pm
6742
Hi, does anybody has experiance with the Deerborn USB (or RS232) to CAN adapter, called DPA? I wondered about the driver API. We have a CAN tool working with...
Peter Lauer
plauer@...
Oct 7, 2008 5:23 pm
6743
I am not familiar with the Motorola processor (we use Texas TMS320F2812), but there is still the possibility that a new incoming message overruns the previous...
Osmar Yang
oy@...
Oct 7, 2008 5:52 pm
6744
Also, Do any of the other nodes have inductive loads? Steve C. ________________________________ From: canlist-owner@......
Corrigan, Steve
s-corrigan1@...
Oct 7, 2008 5:58 pm
6745
Do you count common mode choke as inductive loads? The truck industry has been using the common mode choke for quite a while, and it seems working fine on 250K...
Funny NYPD
funnynypd@...
Oct 7, 2008 7:18 pm
6746
Gianisis, Dino A (US ...
dino.a.gianisis@...
Oct 7, 2008 7:23 pm
6747
FunnyN: An ordinary 8MHz crystal. Why? Do you think it could be generating noise? I don’t count common mode chokes as inductive loads. SteveC: Yes, a PWM in...
JXLL
jxll29@...
Oct 7, 2008 8:24 pm
6748
Could it possibly be the electrovalves thenselves? Do they all turn on at once, or is there a millisecond or two between turn on. I'm wondering how much...
Corrigan, Steve
s-corrigan1@...
Oct 7, 2008 10:05 pm
6749
Hi, I have a couple of questions. 1. How are you powering each node? 2. Is there a common ground between them all? 3. Do they share the same power and ground...
John Dammeyer
johnd@...
Oct 7, 2008 10:25 pm
6750
Brian, Well...what you are calling actuator numbers or actuator addresses are probably IDs. You say "doors have different actuator numbers than the LEDs";...
Allen Pothoof
apothoof@...
Oct 8, 2008 2:17 am
6751
where can I find a copy of the RP1210 spec / api description? regards Peter-- Archives and useful links: http://groups.yahoo.com/group/CANbus Subscribe and...
Peter Lauer
plauer@...
Oct 8, 2008 3:37 am
6752
Hello Br, ... just want to add my experience with that ... the more often ( then having a short of line to GND and 24V power ) is, that the customer just ...
Torsten Krahl
krahl@...
Oct 8, 2008 7:56 am
6753
... Ok, I will take this in consideration. The problem is that I have 5 CAN channels om my PCB and there is no room for >6W resistors. One idea might be to add...
Bertil Bäck
bertil.back@...
Oct 8, 2008 8:52 am
6754
Hi all, I have used a resonator instead of a crystals on many of my boards running at 125Kbps and I have never seen any problems with that. Yet that is. ;-/...
YAP
x112358@...
Oct 8, 2008 9:02 am
6755
I found that reference too, but it does not explain the individual commands. Why is the specification not on the web? Peter Email von Peter...
Peter Lauer
plauer@...
Oct 8, 2008 1:00 pm
6756
Hi, Steve C: There’re 16 electrovalves, but they’re activated one at a time. Besides, it’s an output, and I tried with leds, and the corresponding led ...
JXLL
jxll29@...
Oct 8, 2008 5:05 pm
6757
I'd be careful here. Large power resistors are more often than not wound and have an inductance. You might also want to look at the polyfuse capacitance....
John Dammeyer
johnd@...
Oct 8, 2008 5:22 pm
6758
Bertil Bäck wrote: [...] ... I'm afraid you will not find a PTC fuse with low enough resistance not to affect the required total resistance, but with low...
Oliver Betz
list_ob@...
Oct 8, 2008 5:53 pm
6759
Deutsch actually have at least two type of connectors which has a 120 ohm terminal resistor inside. Funny N. Au Group Electronics, http://www.AuElectronics.com...
Funny NYPD
funnynypd@...
Oct 8, 2008 6:36 pm
6760
John, I tried triple sampling, but unfortunately, it stuck again on the ON position. What I want to point out is that I removed everything from the network...
JXLL
jxll29@...
Oct 8, 2008 7:57 pm
6761
Have you enabled the Watchdog inside or outside of the microcontroller? I am just curious if the micro is dead/self-locked when a large EMI is injected. Can...
Funny NYPD
funnynypd@...
Oct 8, 2008 9:05 pm
6762
is the message to turn off even getting to the board? Add code to transmit a diagnostic message every time the message is received. This will tell you if it is...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
