Hi guys Need some expert advice. I have been using Advantech PCI-1680 for a while on Windows. But I am not able to use it with Linux (Ubuntu 8.10). After...
Hi all, Since I'm now going to be connecting our 5 TKE WCS-10 CAN Bridges together with their CANOpen diagnostic port to a Zanthic CAN4USB into our PC I'm ...
Hi everyone, For general interest I've posted a scope picture here: http://www.autoartisans.com/images/PropDelay1Mbps-35m.jpg The trigger pulse is the falling...
Hello All, Can I use a same transreceiver for both CAN and RS-485? I think using CAN transreceiver for RS-485 communication should not be problematic. Rgrds, ...
In a business application, we have vehicle dashboard instruments which are currently connected with a CANbus. We would like to interface this bus to a USB in...
Hi all, I need to develop communication module for my ECU. How to start implement it? Is J1939-21(data link layer) enough or may need to buy physical...
Hello All, All of my experience with CAN has been with J1939 and CANopen. What are the higher layer protocols that OEM's such as GM, Ford, Chrysler, etc. use...
Hi there - I'm looking to do something somewhat unconventional on an upcoming design. Specifically, I want to have split termination on each node that can be...
... -- Archives and useful links: http://groups.yahoo.com/group/CANbus Subscribe and unsubscribe at www.vector-informatik.com/canlist/ Report any problems to...
Hi all, I am new to CAN. I need to implement CAN communication for my ECU. Which standard I have to buy? I am using Infineon controller. Manivannan D ...
All, I am interested in knowing if there exists any tool that would let one calculate the maximum permissible tolerance of the oscillator used to clock the CAN...
Dear Sirs, As I understood from the DS401 CanOpen standard, at the dictionary entry 0x6000 there are the module digital inputs. Sub index 0 tells how may...
Hi, We have a low-speed CAN network, and we’re in the process of redesigning the nodes’ boards. We use an ordinary 120ohm termination at both ends of the...
LETTER OF INTRODUCTION FROM: Tahir Shahab Khan 76 London Road, CR0 2TB Croydon, Email: infotakhan@... Let me first ask that you permit me to have used...
Hi all, I'm locking for the CAN Message Map of TRUCK (J1939) Volvo for the SCR unit. Have you this document ??? Thank for your answer. <<Immagine (Metafile)>> ...
Hi, when I talk about CAN communication speed I try to always use bit rate. I was cleaning up some .eds files for our products and stumbled on something...
Hi, Iam trying to implement CAN in TMS320 dsp chip.... Actually I tried with only a single node for Evaluation purpose.... I write the code to transmit a...
Hi there - I want to run a single cable with as few conductors as possible that carries CAN and power that will be subjected to all sorts of tortures. It needs...
That is similar to a CAN bridge but with opto-couplers, it will help provide isolation between networks. One concern is about the speed of your network, how...
Hi All;; presently i am writing CAN database to test some EVB,, i am using VectorCANdb++ editor first time can anyone please tell how to enter Receiver in CAN...
Hi, I've had a request for a number of CANRF modules but I dropped that product after ZigBee came out. The biggest advantage of the IEEE 802.15.4-2006 used by...
Dear All, What is the maximum value I can set SJW to in relation to Tseg2 (Phase Seg2)? I've looked at the CAN spec and various postings on the web and I'm a ...
you can contact SAE directly to get one copy from them. Funny N. Au Group Electronics, http://www.AuElectronics.com ________________________________ From:...
Hi, I’m looking for SAE J 553 standard (spec sheet), it’s about circuit brakers. I need to use these circuit brakers in an automotive CAN application....
We have a J1939 product that is usually configured / programmed by our end users. We have a request for monitoring 3 engines on a single vehicle. Is it ...
Dear CANlist members, In order to test the functionalities of an ECU, I created 2 CAPL scripts where one of them simulates inputs messages to the ECU on CAN...
Hi I am having a simple CAN setting: 1. one LPC2129 and MCP2551 i am using as can transmitter 2. one more LPC2129 and MCP2551 i am using as can receiver. both...
