Hello, we have a commercial CAN-node in testing and it corrupts the ACK-pulse by widening it in kind a of "analog" way i.e. falling edge is rounded. In actual...
Hello everyone, I am new to this group and working on my first CAN interface. My project involves a rear LED lamp required to work on MilCAN. I downloaded the...
Dear All I have a developed a CAN devices using PIC18F458 and I want to monitor the bus frame with NI CAN USB 8473 which contains SJA1000 CAN Controller....
Hi everyone, As usual I have a strange request. The client is insisting on using a PLC for a control system. Must be COTS. (Commercial Off The Shelf) so I'm...
Gentlemen, We are making a J1939 engine to NMEA2000 adaptor and would like to test it against a source of test data. Does anyone here know of a test data...
CAN in Automation (CiA) is organizing the event this year on March 5 and 6. It will take place at the Hambach castle in Neustadt an der Weinstraße (Germany). ...
Hello, Is somebody using already COND-field? And are EDS-design and testing tools already supporting it? I tested with ProCANopen and it accepted entries both...
Hi All, I'm looking for a COTS J1939 engine monitor. I'd like to be able to monitor Engine RPM, Temperature, Oil Pressure, Oil Temperature, Charge Voltage and...
Hello, In J1939 protocol, in PGN (Parameter Group Number), PDU format (PF) which is 8 bit value, have following values and significance. PF = 0 - 239...
Hi, When one has the following setup CANStress: Overwrite the RTR bit of the DUT's NM message CANoe: Sends a Ring Message every 100ms with SleepInd=0 &...
Hello, Presently I am developing one CAN application using PIC 18F6585. I have one simulation software called "Proteus 7.8" but there is no CAN debugger...
Hi , I am very new to this forum as well as to CAN protocol. First let me thank you all for giving me an opportunity to learn and share thoughts in such a...
Greetings, I have a question which I haven't been able to find a satisfactory answer to in the archives. It has to do with two CAN nodes with the same node id....
Hello, is there a rule in which direction the mapped entries in a PDO are to be evaluated. When doing left to right the combined control word / setpoint PDOs...
Hello, Can anybody tell me, how to calculate time segments of CAN bit? i.e. Sync_seg, Phase_seg1, Phase_seg2. I have following values for CAN controller 1....
Hi, I have a problem when using codesys v3 with SocketCAN on a ARM module using Linux kernel 3.0.2 with 2 SJA1000 CAN controllers. I have two of these modules....
Hello CAN experts, This may be a very easy question for most of the folks on this list! I am wondering if I am allowed to set up a system to send and receive...
Hi, In the description of Polarity I have identified the following inconsistencies / gaps between the description of the object in the specification 3.0 and...
Hi to all, I have to be able to limit the power of a Volvo Bus engine , for example: at full trottle the power output has to be the 50% of the pot. max. it is...
Dear all ,  I am new to this forum and also to CAN Bus. I will be glad if I could receive some help from you. I will try to give as much relevant...
I am new the CAN protocol messaging and Automotive messages I know that there is a speed tick that occures but only above about 3 kph is there another signal...
LinkedIn ... I'd like to add you to my professional network on LinkedIn. - Xiaofan Xiaofan Chen Staff Engineer at Rockwell Automation Singapore Confirm that...
Dear all , I am new to this forum and also to CAN Bus. I will be glad if I could receive some help from you. I will try to give as much relevant information ...
Dear all , I am new to this forum and also to CAN Bus. I will be glad if I could receive some help from you. I will try to give as much relevant information ...
