... *+-80 V*, This is *short circuit protection * or *transient protection * ? Datasheet not tells detail about *word DC tolerance* . Please suggest....
8150
raj katoch
katochd46@...
Apr 30, 2012 2:56 pm
Thanks, i will go through this specs. //raj...
8149
danjperron
djperron@...
Apr 30, 2012 2:12 pm
If you google "RC tee filter canbus" you will eventually find http://www.can-cia.org/fileadmin/cia/files/icc/10/cia_paper_lepkowski.pdf check page 2-19 ...
8148
Dinesh Guleria
din.gulu.er@...
Apr 30, 2012 9:32 am
Hello, Thanks for the reply. Just one more thing. How can we detect following condition at our CAN node ? What kind of effect will it have at our CAN network...
8147
heikki.saha@...
Apr 30, 2012 8:04 am
Hello, Pre-requisite is properly implemented linear topology with as short drop- lines as possible. Additionally, 120R impedance-matched twisted-pair or ...
8146
Dinesh Guleria
din.gulu.er@...
Apr 28, 2012 12:59 pm
Hi, Preparing circuit for my CAN Node. How to add extra protection on can network. For protection against high energy spikes (transients) & short to ground ? ...
8145
Dinesh Guleria
din.gulu.er@...
Apr 28, 2012 11:17 am
... I worked on Ford vehicle and most common are 125 & 500 Kbits/sec On Sat, Apr 28, 2012 at 12:09 AM, Rufus V. Smith...
8144
Dinesh Guleria
din.gulu.er@...
Apr 28, 2012 8:01 am
... Are you sure Honda civic is having Can interface for diagnostics on OBD-II connector. There are five signaling protocols that are permitted with the OBD-II...
8143
Dinesh Guleria
din.gulu.er@...
Apr 28, 2012 7:55 am
... * * Ground of PCB of NODE. *>>So emission means high frequency noise or something else also ?* Means Noise filtering /Dinesh...
8142
Dinesh Guleria
din.gulu.er@...
Apr 28, 2012 7:43 am
... * * Ground of PCB of NODE. *>>So emission means high frequency noise or something else also ?* Means Noise filtering /Dinesh...
8141
Vikram Rajput
vsrajput@...
Apr 28, 2012 7:25 am
I was under the impression that all 2008 and newer model year vehicles use CAN. BTW I tried 250kbaud also. Same error BUSHEAVY. Thanks, Vikram On Fri, Apr 27,...
8140
Vikram Rajput
vsrajput@...
Apr 28, 2012 7:18 am
Hi, I have PCAN-explorer and PCAN-USB. Both are from PEAK-System. Both are working fine for other CAN system (Board developed by me using PIC18F4580), I can...
8139
Rufus V. Smith
rufuss@...
Apr 28, 2012 7:11 am
In my limited knowledge of OBD-II, there are multiple different physical layers, not just 500 kbaud CAN. The first thing I'd do is try 250kbaud. Then I'd look...
8138
raj katoch
katochd46@...
Apr 27, 2012 12:48 pm
Hi, I was going through CAN bus specification. Few things i will like to clear. CAN bus is based on differential signalling does not require common ground. So...
8137
Priyanka
priyanka_patankar1990...
Apr 25, 2012 10:11 am
Dear Vishwesh, This is the modified table which was provided by you. According to my knowledge, this is correct. Please correct me if there is any problem in...
8136
Hadarits Kft.
hadaritskft@...
Apr 24, 2012 9:24 pm
Dear Sirs, We deal with tachographs in trucks. In the most cases the tachograph is the one end of the CAN network and inside the tachograph the termination...
8135
Uwe Wilhelm (GMX)
u.wilhelm@...
Apr 24, 2012 10:05 am
Hi, Sub D9 CAN - according CiA DS 102 The CiA DS-102 standard includes a pin assignment for 9-pole Sub-D connectors for the connection of nodes to the CAN bus...
8134
raj katoch
katochd46@...
Apr 24, 2012 9:37 am
Thanks, how to make this joint of nodes to the CAN bus through sub-cables ? http://en.wikipedia.org/wiki/File:CAN-Bus_Elektrische_Zweidrahtleitung.svg what are...
8133
raj katoch
katochd46@...
Apr 24, 2012 9:36 am
... thanks,This is really good one... how i missed it... it contains every thing. But one thing i did not found in this specs ... i.e. max current driving ...
8132
Uwe Wilhelm (GMX)
u.wilhelm@...
Apr 24, 2012 8:29 am
www.cd-systems.com/Can/can-cables.htm Von: canlist-owner@... [mailto:canlist-owner@...] Im Auftrag von raj ...
8131
John Dammeyer
johnd@...
Apr 24, 2012 7:56 am
http://www.nxp.com/documents/application_note/AN96116.pdf "ELS! The Solution" Automation Artisans Inc. http://www.autoartisans.com/ELS/ Ph. 1 250 544 4950 ... ...
8130
Heinz-Jürgen Oertel
oe@...
Apr 24, 2012 7:03 am
Betreff: AW: [CANLIST] Compiling PCAN for USB Hi, please use make PCC=NO ISA=NO DNG=NO PCI=NO Regards Uwe Danke! Heinz-- Archives and useful links:...
8129
raj katoch
katochd46@...
Apr 24, 2012 6:39 am
got from last few mails related to cable, just few more points. Hope you dint mind. ... there's 3.5V across the two 100 Ohm resistors or 3.5V/50 Ohms = 70mA. ...
8128
heikki.saha@...
Apr 24, 2012 4:52 am
Hello, At least following cable types are designed for CAN and well proven, hope this helps. Belden: 1345F 3082A/F 3084A/F Lappkabel Unitronic: BUS FDB CAN ...
8127
John Dammeyer
johnd@...
Apr 23, 2012 9:42 pm
Just remember if you use 100 ohm impedance cable (like CAT5) and 100 Ohm termination resistors at each end you reduce the maximum number of nodes. If the CAN...
8126
David Harris
dpharris@...
Apr 23, 2012 9:28 pm
You can use CAT5. The more important that the impedance is constant over the bus, rather than a perfect match to the termination value. The constant...
8125
raj katoch
katochd46@...
Apr 23, 2012 6:36 pm
Hi, Can was designed to work with 120 ohm cable. Please suggest what is the right standard name for this type of cable. I thought about CAT5(e) cable for...
8124
raj katoch
katochd46@...
Apr 23, 2012 6:34 pm
Hi, Can was designed to work with 120 ohm cable. Please suggest what is the right standard name for this type of cable. I thought about CAT5(e) cable for...
8123
Uwe Wilhelm (GMX)
u.wilhelm@...
Apr 23, 2012 3:05 pm
Hi, please use make PCC=NO ISA=NO DNG=NO PCI=NO Regards Uwe ... Im Auftrag von Heinz-Jürgen Oertel Gesendet: Montag, 23. April 2012 16:18 An:...
8122
oe@...
Apr 23, 2012 3:00 pm
This message has been digitally signed by the sender. ... Hi-Tech Gears Ltd, Gurgaon, India...
