I had thought about doing something like that Steve, and will investigate further down the road. I am waiting for two completed drive setups that I am wanting...
Hi All, I though that the copickt of my Crystal was quite empty... and made a pilot for it. It will surely fly better now... Of course, the pilot will get some...
To a degree it would, but I have some other parts to make that call for the hot wire cutter first. What these pulleys are that I plan to cut are remakes of...
Boneheaded- do you have a name? I might suggest you do a simple rectangle with an accurate hole in it, with specific dimensions as a test piece. This will...
Christian, yeah, I have a name. My friends call me Doc, and I apologize to all of you for not having put a name with the posts prior. I am planning, as you...
Doc- Good luck and be sure and post photos of your progress so we can learn too ... -Christian -- www.BrilliantDesignOnline.com Solidworks Design & CNC...
WIth the input I have received from this group in just a few posts I will certainly be posting pics, and information as it comes about. I appreciate the...
After I posted on the HobbyCNC group, asking Dave for the proper GGCV2 settings to use for the HobbyCNC board, I got a couple emails asking about doing the...
Just starting this thread, I'm sure Dan will have more here than me. I've got the GGC V2 up and running, using the components from Dan.. There are a few issues...
Hey fellow foam cutters. First many thanks to Don, he discovered the Data Sheet error just when I thought I was going to be scraping a mess of LCD units...
Just a couple comments ... It was not planed. The contrast has been always fine on the LCD I used until now. The resistor/potentiometer is the right solution. ...
Hey Don Tis I again.... Nice start on Motor Tuning and will get you going in the right direction. First a couple of things, sort of a FAQ session and even...
Thanks for remembering the accel settings. I have had mine at 100, and never thought to test them ;( Yes the GGC will only talk to GMFC, but any software...
One small addition... You can change the pin assignments in the GGC V2 utility, so a different cable shouldn't be needed if using a different board. Don...
Yes, I made that request a long time ago but Gilles informed me he was already working on it for the V2. Sorry , I should have spelled that out. V2 should...
Hi, I am about to wire up an LCD. The documentation on the GCC-V2 for the LCD doesn't show the same data that came with my LCD. Can you tell me which pins on...
Hi Domenic If yours is a 16x1 LCD, they are all SUPPOSED to based on an Hitachi design. Your Data sheet should also be numbered next to the Symbol's though...
That's great info Don. I'm not sure what brand mine is as it has no traceable numbers or brands printed on it. Your info contains exactly what I needed. Thank...
15962
CNCFoamcutters@yahoog...
May 10, 2012 2:33 pm
Hello, This email message is a notification to let you know that a file has been uploaded to the Files area of the CNCFoamcutters group. File : /Stealth...
The sub panel kerf calculations have been improved and now doesn't trigger the over- and under-speed alarms unnecessarily. I'd better explain what sub panels...
Hi Mathias, ... The limit switches are only supported by the EXPERT version of GMFC. ... Yes, it should work fine if your Hobby CNC interface does not have...
Hi Stan From the manual: Dan Powering the heat wire The heat wire is powered via the PowBow connector in the GGC mode. The maximum voltage is 50V DC. Beware of...
My foam cutter is like the attached photo, and has stepper motors labeled: Powermax II "P21NSXC LSS NS 03" 1500 RPM 1.75A 65V(dc) Would this be a good match...
... Hey Tony The Foam pics didn't work out for me, all I see is a machine itself. The issues you listed sound to "me" like either wire connections, solder ...
