Here's the video --> http://youtu.be/H9B9d7vQBxk On Fri, Mar 22, 2013 at 7:55 AM, Martin Tigasson...
16351
Scott Peterson
blu_swede
Mar 23, 2013 7:33 am
Woo!...OK, that's a problem! Do tell, are we looking at the big end or small end? (hoping small) Also; what is the taper ratio? As a general rule tapers...
16352
Martin Tigasson
m4rt1g
Mar 23, 2013 8:23 am
You are looking at the small end. The taper ratio is 1,67:1. The speed at the wider end is about 6 cm per minute and about 4 cm per minute at the smaller end....
16353
Scott Zastoupil
szastoupil
Mar 23, 2013 6:21 pm
From my experience cutting that slow is extremely difficult. I found that that cutting 5 inches to 6 inches per minute (12.7cm to 15.4cm/min) is about the...
16354
Martin Tigasson
m4rt1g
Mar 23, 2013 7:41 pm
0.125 inches is damn thin. I would have to do some serious work on my foamcutter to get good cuts at that speed. I have planning to do that anyway. Thanks for...
16355
Scott Zastoupil
szastoupil
Mar 23, 2013 8:31 pm
I never said it was easy, but it can be done. :) Lot's of practice and very happy with 1 out of 2 good parts. It probably took a month tinkering and a...
16356
Scott Peterson
blu_swede
Mar 23, 2013 9:41 pm
Oh!...a local boy!...I'm in Wausau-ish, if it doesn't say by my avatar. Martin, I've had that trouble you describe. It will occur to some extent...
16357
CNCFoamcutters@yahoog...
Mar 28, 2013 11:11 pm
Hello, This email message is a notification to let you know that a file has been uploaded to the Files area of the CNCFoamcutters group. File : /Stealth...
16358
Anker Berg-Sonne
ankerbs
Mar 28, 2013 11:12 pm
It has been a long time since I have published an update. You can download 1.3.157 from here: ...
16359
Παξ John
paxijohn
Mar 30, 2013 7:01 am
Thanks Anker What differs from the previous version? ________________________________ Απο: Anker Berg-Sonne <anker@...> Προς:...
16360
Anker Berg-Sonne
ankerbs
Mar 30, 2013 12:07 pm
Mostly bug fixes. The last major change (flip, one step vs. two step wizard) had introduced a number of bugs which have been corrected as they have been...
16361
rod11heli
Mar 30, 2013 9:43 pm
Hi All Am trying to cut a tapered rudder with an inset 6x25 balsa leading edge. The profiles are simple DXF's with the same number of points. However GMFC Pro...
16362
Dirk Schipper
schipperdirk
Mar 30, 2013 10:13 pm
When GMFC cuts counter-clockwise the kerf is on the outside, when cutting clockwise the kerf is on the inside (when I remember well). Change the cutting...
16363
rod11heli
Mar 31, 2013 7:17 pm
Thanks for the input Dirk. Yes I did have to change the direction of the DXF polyline to get the anti clockwise (top first) cut. However the problem...
16364
Gilles Muller
gillesmullerfr
Mar 31, 2013 7:22 pm
Rod, ... Can you check the order of the points within GMFC? You don't have to inverse the direction in the DXF. This can be done in GMFC in the alignment mode....
16365
Gilles Muller
gillesmullerfr
Apr 5, 2013 5:33 pm
Hi all, Something I have made base on my recent experience: http://start1g.ovh.net/~gmfcsoft/blog/?p=819 You comments are welcome as usual, Gilles -- Gilles...
16366
Bubba
jmagey
Apr 8, 2013 1:25 am
I've had my machine for quit some time however just recently gotten time to get back to it. I've cut wings on it before and they turned out great but now...
16367
Dan Field
kombatjr99
Apr 8, 2013 2:47 am
Hey Did you ever resolve the table setup issues understanding "Between the wire supports". Break it down. 1. You say all motors will go out or up a distance...
16368
Eben Brand
bazziebazooka
Apr 8, 2013 3:05 am
Another possibility would be the machine screw pitch - sounds like the setting for that may be off....
16369
a.senthil kumar a.sen...
senthildecee
Apr 11, 2013 2:35 pm
hi, may i know what kind of software and stepper motor driver board you are using now. based on that information i could help you to solve your cnc...
16370
Robert Blumer
robertblumer11
Apr 14, 2013 6:02 pm
Gilles, I want to do this on the PRO version? Can it be done? Regards Bob Billings, MT...
16371
Gilles Muller
gillesmullerfr
Apr 14, 2013 8:51 pm
Hi Bob, It can't be done directly using the PRO version... there are at least some reasons for an Expert version... ;-) If you want to do the same, you need to...
16372
Bubba
jmagey
Apr 16, 2013 12:47 am
I am using GMFC Pro and have most everything setup, I think. There are a few issues that I can't seem to get a handle on. Could really use some more help here...
16373
Gilles Muller
gillesmullerfr
Apr 16, 2013 5:36 am
Hi Jack, ... GMFC tells you in the cutting dialog where the limiting points are. This should help you to understand the problem. Is your wing profile a custom...
16374
Gilles Muller
gillesmullerfr
Apr 17, 2013 9:39 pm
Hi Peter, ... Yes, only one. ... all versions can be read by the latest version of the software (for a given version). You can't read GMFC expert files from...
16375
Gilles Muller
gillesmullerfr
Apr 22, 2013 2:39 pm
Hi All, This version corrects few bugs and brings several new functions. New functions: - Spar filling (GMFC Expert). This dialogs permit to cut a piece of...
16376
Bubba
jmagey
Apr 25, 2013 2:20 am
Thanks for your help Gilles. As far as the time computed to cut a panel, I had the time set to 500 instead of 250 because I can get faster cuts that way. Is...
16377
Gilles Muller
gillesmullerfr
Apr 26, 2013 1:19 pm
Hi all, This version corrects few bugs on the dialogs. Enjoy, Gilles -- Gilles Muller http://www.gmfcsoft.com/...
16382
cburgmike
May 19, 2013 2:30 am
Hi Group! I was cutting some EPO foam today, and wondered how toxic was what I was breathing? I had the windows open, and it didn't seem too bad, but I am sure...
16383
William Scott
william839868
May 19, 2013 6:29 pm
I always work on the basis that if it smells bad, it's probably not good for you. Haven't finished my cnc yet, but when cutting with the drop arm I would ...
