Hi, i'm new to this group, and i'm not a computer geek. I am hoping, answers get e mailed, because i may never find where they went! ok, I bought cnc pro back...
If the flash drive is a USB device, probably not. There is a nifty board at dealextreme.com that takes an SD or perhaps usb drive and gives it an IDE...
I run cnc pro on my newer computer. I have cncpro loaded on on a fat32 partition c:\cncpro I have a c:\cncpro\gcode dir I boot from a win98 startup floppy,...
... It's my understanding of things that the reason this software is run under DOS and not windoze of any flavor or linux or whatever is because of the things ...
... Generally, yes IF it has PATA/EIDE drives. SATA drives can be problematic. DO NOT GET RAID! You will still need a floppy and drivers for the USB stuff,...
... In many cases the IPL device (in this case FLASH/USB) can really hurt timing but can load into a RAMDISK and be run from there. Microsoft did that as part...
I have one of those IDE to CF adapters. I haven't tried it yet but one of our members is using his with turbo cnc, apparently without problems. The name on the...
We got them at Geeks.com and at the time, it was F-ADIDE2CF-B1 -- Best Connectivity IDE to CF Adapter and they were $12 each back in August of 2006! Like Doug...
I have an IDE CF card adapter. I had some problems with it in the beginning due to flaky solder joints. Resoldered it all and it work perfectly. Many run hours...
Yes, I have one and used it successfully with TurboCNC (plugged the CF card adapter right into the cable where 'C' drive would be). I took it one step further...
Hi All, Have a question for those in the know. I have completed a custom build and have wired the limit switches using some spare 20g speaker cable. When I set...
Yes, you are probably running logic level signal through the limit switches, which is a VERY small signal. the signal is so small, it don't make it through the...
... Did you check the sense of the limit switches? Your problem might be how TurboCNC has your limits configured. Are your limit switches running directly to...
Duh, yes, shielding the signal wires would be great! I probably would not shield the stepper motor lines, at least not in the same cable. Sorry, what you...
I tried turbocnc, and had problems with limit switches a search of the group turned up 1000+ questions on limit switches that is why I use cncpro, it works...
I bought cncpro about 5 years ago and between moving new family members, I'm thinking of getting the old mill back up and running. I see now it is free just...
Hey guys. I am a new member just getting into CNC. I am the looking around at the moment but would like to see what this cncpro is like. I'm not sure if I'm...
I know this is an old thread. Watch out there are two CNCPro programs. One comes with a CNC Junior. The motor driver is a black box with a fan. Inside you will...
I have the "other" (CNCJunior) software and hardware, if that's what you are looking for/anybody needs. I was going to ebay the hardware, I think the software...
go to the files section of the group : http://tech.groups.yahoo.com/group/CNCPro/files/ and then either download the cncpro_tracy.zip or look in the "users"...
Hi Ned; I know you are already "into" your test, but do you have any scrap CRS left over? I would love to know how Tribol, Vactra, CRC chain saw bar lubricant...
hi to every body, I recently bought a big ploter 4x12 the las t owner was sure the machine was running, so I boughted he gave me 3 old srtyle floopyes and 2 of...
Hugo; Are you planning to convert the plotter to a router table? If so, then you can download cncpro from the files section of this group. We will also need to...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
