Doug suspected that the problem lay somewhere in Microsoft's territory, not his program. The problem actually involves many keys, not just the numeric ones ...
Mark, where in the program can I see the "max pulsing rate test" results? I started the prog several times and searched the menus. Nothing found. RichD...
In my effort to convert the existing CFG and INI files of to a new format with [sections] and key=value pairs I've found a few variables which are not...
... Hi, Carl: I believe that he is assuming that you'll always be using three linear axes for a mill and 2 axes for a lathe. These, he's "forced" to be named ...
i have built a cnc plasma cutting table a couple of years ago and used the trial cnc pro to set up my machine, now i`d like to get the unlocked version, can...
You want to download CNCproBeta.zip in the files section of this group. This version is the last release from Doug, except the key lock has been removed. It...
When I try to download it, I get a "Document not found" message. Can you double check and make sure it is there? ... folder. ... interface. ... used...
... Hi, Curtis: I just downloaded the file; it's still there and should be available. -- Jerry Jankura Strongsville, Ohio So many toys.... So little time.......
... I'm using FireFox as my browser. It's got a "flashgot" plug-in which makes use of FreshDevices Fresh Download. -- Jerry Jankura Strongsville, Ohio So many...
... What ... Hi Jerry, Like you I tend to use Firefox on my Mac, Linux, and Window systems. I like the FoxMark plugin to sync my bookmarks across all my...
Thanks guys...using Firefox and having problems when I click on a link, but tried again after reading you guys messages and if I right click and "Save as" it...
Does anyone have a version of Borland's TurboVision 2.x that compiles correctly when using Borland's C++ 5.02? The more I think about a menu-driven interface...
... coming to ... TurboVision to ... CNCFree ... following ... not so ... the ... Jerry, Are you using the TurboVision 2.0.3 source code over on Sourceforge? ...
... No, I'm trying to use the stuff that Borland released. I've downloaded the stuff from Source Forge, but haven't done much else with it. -- Jerry Jankura ...
Hi all, it was only after a chance find of one of Mike Phillips web pages, that I asked about CNCpro did I became aware of this group. I have a licensed copy...
I know it is wrong to replay to myself but I have now found the files links to the new code and even the last two versions on CNCpro from Doug Y. I seemed to...
Hi i am new in th egroup, I´m planing to build a router and I wan to to know if CNCPRO can be used with a quadrature driver or phase driver. thanks.... ...
Fernando; cncpro is only capable of step and direction output signals. If you are proficient with C programming you could probably modify the source code to...
... To my knowledge, CNCPro allows only step/direction motor drives. TurboCNC (www.dakeng.com) will work with either step/dir or phase motor drives. -- Jerry...
Thank you for allowing me membership into your Group. I am new to CNC so I will be learning as much as possible. So, I need all the help I can get. Thank you...
Greetings, I'm glad this group is here. Too bad yeager automation is no more. I have a licensed copy of CNCpro from 2002. My machine/software started behaving...
Larry, My only suggestion is to download one of the versions in the files section that has the "license" negated! I don't think to much has been done to...
Bubba, Good idea. I downloaded Alan's version and was able to get up and running. (Good work, Alan! I like the changes you've made.) Larry Grennan ... ...
Please forgive these thoughts, not being a programmer packagethey may not be as sensible as I think. I have a job to use my old cnc mill again and have the...
Adrian, Not as good as a matched simulator but two thoughts spring to mind. Make a custom post for your cam software which uses more generic codes (rather than...
... Hi, Adrian: Since we're talking about software, everything is possible. However, consider this - a lot of folks have written G-Code to use CNCPro's version...
... structure ... Hi Jerry and Jeff in the previous post. I tried to do a bit of a search on RS274 and see a general trend to some new form of integrated...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
