Dear Adrian, You can use route-maps associated to prefix-list or access-list to match applications. But following to Cisco recommendations, the NBAR and MQC...
easy usign PBR.=Â route maps. you use acesslist to mach the traffic you want. and use the command "set" so say in wich interface you will send that traffic. Â ...
Dear Imran, Regarding your question, you need to configure NBAR(Network-based Application Recognition)using MQC(Modular Quality of Service)which will allow you...
U can use 802.1q protocol as the trunk protocol which is a ietf standard one . Â If u want to make interVLAN communication then u need to give IP to the VLANs...
use dot1q 801.q it is the EITF standar trunk permit all in the trunk uplinks. to the first switch. ... De:: Ben Burt <ben@...> Asunto: [Cisco_CCIE_Lab]...
Hi Guys, I have a few vlan questions for you. Example Scenario. I have a 2900 switch with 3 vlans I have added a second and third 2900 switches I can use VTP...
Yes. If you are peered with 4.4.4.4 and that router goes down, then your virtual link to area 0 is down. Regardless of who is elected the DR. ... From: Lee...
Here's something I can't seem to find the answer to with google ;-).. If I have a multi area ospf network, AREA 0 ... AREA 100 ... AREA 3 If I configure a...
What is proxy ARP? Proxy ARP (RFC 1027) is a way to make a machine physically located on one network appear to be logically part of a different physical...
Hello all, I would like to know answers of following questions: What is proxy ARP? What is difference between Proxy ARP and RARP? Why do we type "no IP direct...
hi everyone, I got a problem with CW LMS. I've installed CW LMS 3.0 on windows server 2003. When I tried to log in at first time, a password...
Hi Thx for u r re. but where can get the exact mat for my requirement of switch matching all technical specifications as mention in above sheet Please let me...
by this wording -Lan Switch Middle Range -Back plane in GB 40(20 GB Full Duplex) -The equipment shall be Carrier class with modular design. they...
Hi All I want to perches the middle range switch for my organization but having the above attached configuration. Can any on tell me the model of the switch ...
Hi sh running config file on Layer 3 switch(6509) should show as in the following example,  boot system flash bootflash:c6msfc-dsv-mz.121-20.E.bin  boot...
why don you try with ip address. instead of using matching protocol use ip addresses.. one for yoyr computer and another that mathc your bittorrent server.? ...
Hi friend, did you try to classify traffic with an ACL, just for checking? Instead of matching protocol, try to do it with a pre-classified ACL traffic. At...
Hi guys, Sorry for the long post. Im trying to adjust my QoS rules and am running into problems. I have a 512/128 DSL connection and 2 PC¹s 1 is my desktop...
I am not able to do conf for POE Conf for 3560 Switch. Cisco IOS Software, C3560 Software (C3560-IPBASE-M), Version 12.2(35)SE5, RELEAS E SOFTWARE (fc1) ...
I would like that if any cisco Phone atached to that cisco Switch it will get automaticaly power from Switch... Adrian Lopez <lomadrian@...> wrote: ...
Hi Ravindra, you cant configure power command in enable mode , you have to go in en --> conf --> interface mode of any port for configure the power inline cmd,...
Exactly what do you want to do..? I mean why do you wath the power inline comand configured.? and giveme an extract of the comands you are introducing after...
we are using Cisco 48 port 3560 POE switch,but when i trying to enter command Power inline auto it says invalid command..? did i have to conf more parameter in...
I think it will be both review the CCIE blueprint. ... De:: HappyLoomer Loomer <happyloomer@...> Asunto: [Cisco_CCIE_Lab] voice over frame relay is...
Well , it is a simple task like others said , using IOS IPsec features as long as your IOS image has a ***K9** version. Your current ios version support it....
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
