Dear; just type ... #copy running-config tftp #copy tftp running-config Regards ~~~~~~~~~~~~~~~~~~~~~~~ Muhammad Asim Gul Email: asim@... Mobile:...
Muhammad Asim Gul
asim@...
Nov 3, 2003 7:10 am
1645
Hi Dhananjay, I could not follow your point.. can u explain a bit more when you say that "opportunities ... Thanks for your time, Vikas ... ===== Impossible...
HI All. I'm working in University and i'm willing to establish a CCNP Level Network LAB. Can any one of you give me exact details and specifications. Regards...
Well it depends, do you want to continue on and get your ccie or not? Current O/S is 12.2 for CCIE and will go up, never down, Do you want to do VoIP, then...
let me restate and redesign the problem. buddy, assume only that i have a functioing relationship and working bgp . and my current scenario is that i have one...
Help !! Thanks I have 2 cisco 1501 routers. Router A: e0 has ip 192.168.2.8 s0 has ip 192.168.10.2 bandwidth 56 clock rate set 56000 gateway last resort is...
I would like to connect three 2501 routers together to create a test network. The 2501's all have 2 female serial network interfaces. What type of cables do I...
You need 3 serial- v35 dte and 3 serial- v35 dce ciscochris2003 <CTLahm@...> wrote:I would like to connect three 2501 routers together to create a test ...
I am trying to find the best monitoring tool for a nationwide WAN. All of the routers are Ciscos, and I want to be able to monitor all port activity. I also...
Chris, One of the most popular shareware performance tools is MRTG. There are a number of other products such as Concord, SolarWinds to name a couple others. ...
I've had good experiences with Intermapper (www.intermapper.com). It's strictly for monitoring (ie, no historical reporting) and can e- mail, page, play an...
For Monitoring a Cisco network, you need to remember the following: 1. Network Elements (including Cisco Routers and Switches) are manageable using SNMP, CORBA...
OK, I am studying for my ccsp and I have a question. I am configuring router on a stick to a 2950 using dot1q. I get that working using a subinterface on a...
based on the premise, that you have configured your VRFs and RDs correctly, you should be able to perform the following from the 4500... This should work at a...
... this is the debug output from an debug ip packet, 00:19:38: IP: s=80.0.0.1 (local), d=80.0.0.2, len 56, unroutable 00:19:38: IP: s=172.16.16.2 (Serial0),...
Did you create a VRF static route pointing to the CE destination subnet? WITHOUT.. MPLS, the Router(4500) uses the directly connected "C" route from its global...
It is directly connected. I am just trying to ping the subinterface between the CE and the PE. See the show ip int brief below. MPLS_WEST#show ip int brief ...
I think something wrong with your config or your e-mail maybe :D In your 1st e-mail you used fasteth sub interface : "interface FastEthernet0.100 encapsulation...
hi guys i have just started prep for my ccie r&s and need your advice on the books.Which is the best comprehensive guide for the routing and switching exam.I...
I have an Asynchronous Serial 32A card in my 2600 router which has 4 68 pin ports. I have an octal cable which is 68 pin to 8 RJ-45 ends into one of the Async...
Yep, everything works fine now, there is a frame map, no subinterfaces. Subinterfaces make you lazy then the ccie labs get you ;-( ... configs of ... - BGP ......
Vincent, In order to block these Instant Messaging tools, you basically want to set up access list to block traffic to their login servers. AIM needs to...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
