You can use 2500 series routers but you'll need them for complex senarios. Basically you need at least 2 x 2621or 1 x 2621 and 1 x 2610 1 x 3550 Catalyst...
I've been told you need two 3550's for the CCIE lab for routing and switching. Does anyone know why they need two? And as an idea for anyone looking for a...
You need two switches in order to perform etherchannel, see test the effect of learning VLANs via VTP, etc. -Ish ________________________________ From: Dave...
You don't necessarily need ANY 3550s. It just depends where your strengths are. There are two in the lab setup, but you don't necessarily have to have two in...
Marvin is correct in that you do not need two 3550s to practice trunking and etherchannel. You do need at least one 3550 to practice some the platform...
Hey guys, im getting back in the game after being unhappy where I work ( another story for another thread ). Anyway, I have a question. I was reviewing this...
Why a 2621? Is there a scenario that requires two fast eth? Why not a 2611? I have take the lab twice and I am now gearing up to do it again and I want to get...
Could someone please tell me the examination pattern of CCIP BGP 642-661 and possibly any reference book. I've Navigated the entire internet but couldn't find ...
Hi Friends, As everyone knows, the passing score fluctuates in case of Cisco exams. Could someone please tell me the minimum paasing scores for MPLS...
Hello I am preparing for Cisco Content Networking (9E0-600) exam. If anyone has taken this exam then please guide me. If any has any material or book related...
Recently, we have noticed that the number of questions posted far exceed the number of replies. This is possible due to group members having greater...
cisco 2520 as frame-relay router have a next setup 2520 as frame-relay switching router 2501 r1 connected to s0 and 2501 r2 connected to s2 of 2520 r1 s0 dlci...
MPLS was 867, just learn your MPLS/OSPF stuff well. QoS was in the 700's, and I forget what BGP was, but it wasn't difficult with proper study. ... ...
When you show your map, is it really already in there? ... __________________________________ Do you Yahoo!? Yahoo! Search - Find what you’re looking for...
Hi! all, Thnks a lot for such initiatives.....really wanted some thing like this...... cisco_ccie_lab <vze3wmc7@...> wrote: Recently, we have noticed...
If you want to emulate full mash FR on 2520 your mismatch is s0 configuration. Correct item is frame-relay route 112 interface Serial2 211 ^^^^^^^^^^^^^ ...
hi everybody! I have planned to take up the ccie routing and switching exam three months from now.so i would appreciate any suggestions regarding books and...
Hi, I've already passed the written exam and I advise you the following: There is no single book on the market that covers all the material that is on the...
I am setting up a perimeter internet router with two providers (AT&T & MCI). MCI is currently our primary provider. I currently am using just one interface,...
Eugene try to clear the inv-arp table first then apply the maps Adam ... Do you Yahoo!? Yahoo! Search - Find what you’re looking for faster. Eugene try to...
Dear Folks, What are the possible causes that make point-to-point ping test not 100% ? I've check that linecode and crc setting was correct. The BERT test are...
Hi You should specify the administrative distance with second default route. Regards Ramanpreet Bajaj ... __________________________________ Do you Yahoo!? ...
What is the link type? Ethernet, serial or else? if your are using Cisco router to ping relatively large packets on a low bandwidth link, there will be a...
Dear Friends, I am third year comp engg student. I had a query regarding monitoring of a router. I intend to make a software for monitoring of a router. This...
Harsh, For Cisco device monitoring, I would recommend using SNMP (Simple Network Management Protocol). For network monitoring, please take a look at a tool ...
It sounds like you are trying to grab SNMP information from routers. Very similar to like what MRTG or VitalNet(Lucent product)does. You might take a look at...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
