just use a rollover cable and connect aux to aux Henry Valdes <henryvaldes@...> wrote:Hey Steppenwolfe, This goes to show that you are never to old to...
I'm having a problem getting my OSPF P2MP working over Frame. How should I map the DLCI's on the Frame switch using the "frame-relay route" command? I have...
Here's a config: Enable frame switching globally: conf t frame switching Then under each interface, enable frame, set the clocking, tell the interface it's a...
Hey John, I actually pre-spliced these cables myself many years ago...:>) But it's good information for everyone just the same. Thanks. Regards, Henry ... ...
I have 2 nt-4p modules for my Cisco 4000, they work fine, I bought another, but it seems the 4000 only allows me to have 2 modules installed and working, ...
Thanks Step. I was thinking Frame-relay map and not Frame-relay route. ... From: steppenwolfe_2000 [mailto:steppenwolfe_2000@...] Sent: Wednesday, June...
I think this might have more to do with power consumption then software. I had a similar problem on a 4000 with three modules installed. It worked for a while,...
Hello Cisco CCIE Lab members The results of the May 2004 Cisco Press contest will be out soon. The leading contenders are Henry Valdes, Steppenwolfe_2000 and ...
.Anybody have any ideas on the current job market for a CCIE in R&S? I've been looking for work as a CCDA and CCNP and have not had any luck in the Atlanta...
Hey Michael, I know I am preaching to the choir, but here is my two cents on this issue. And not in any particular order. In New York City, the technology...
I have (3) 4000's fully loaded, and have never experienced any problems with them? I bought them on Ebay, and I guess I can knock on wood for not having the...
Review this data and tell me (1) what are the possible problems based on the data; and (2) what are the probable solutions based on this data. Your reward is...
I have 14 sample labs for CSS1. Would anyone want me to post them? Actually, I have tons of sample configs on almost everything concerning cisco...:>) Regards,...
Here is some information you need for the CCIE Written Exam: CCIE Qualification Exam Exam Area: IOS Features / Cisco Devices Overview Sample Questions ...
Here is more review information on the CCIE Written Exam that I have: CCIE Qualification Seminar Desktop Protocols IPX Appletalk Updated 10/5/00 Desktop...
Here are 60 CCIE Practice Questions. Cut and paste this to your computer and answer the questions. Then just post the number and your answer. We will then...
Bridging and DLSw+ Source-Route Bridging (SRB) Important concept; must understand it for written and lab portion of the exam! Source device determines and...
This is just a small fraction of the information you will be tested on if you decide to pursue the CISSP Certification. Obviously, you would be better suited...
Hi, I have 2621 Router, on which I have one serial interface with four sub-interfaces. Serial interface is showing the capacity of 1544 Kbps and sub interfaces...
These questions seems to be outdated. For example, IPX is no longer tested in CCIE written exam. But of course it will be good if you know them all. ... ...
I'm working on two routers, and have two serial interfaces active between the two routers. I got this error message : %IP-4-ZERO_ADDR: Zero MAC address for...
I'm about to pull what little hair I have out of my head...after shelling out $$$$$$$$$$$$$$$$$$$$$$$$$$ for my own lab gear, my 4500 (frame switch and...
Bandwidth is only what the physical interface has, in this case 1544 Kbps. By default, serial interfaces, including subinterfaces, default to a bandwidth...
In addition, your technically oversubscribing your bandwidth because the other sides of those 4 subinterfaces could all try to send 1544 Kbps of traffic, in...
I received my terminal server yesterday (2511). I'm having a problem switching sessions and disconnecting existing sessions. Here's h1ow I have it configed: ...
first, what telnet application are you using, because some have different escape characters. for example, minicom on linux uses cntrl-6 + x. Second, has the...
Michael -- The cntrl+shift, then 6, then x, command works for me. However, once connected to the terminal server, I use the "connect" command to access other...
Could be you are missing no exec on the line.. Here's a working config: hostname R2509 ! enable secret cisco ip host r1 2001 10.1.1.1 ip host r2 2002 10.1.1.1 ...
I want to set up a Cisco router as a gateway router for my home network. I have a static public IP address (66.93.138.200) that I will use for NAT on the...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
