The following Cisco_CCIE_Lab poll is now closed. Here are the final results: POLL QUESTION: Should universities offer college credits for vendor product ...
Cisco_CCIE_Lab@yahoog...
Sep 1, 2004 7:54 am
2595
I have cisco 7200 series. 3 wan connection 1 going to london ---- area 69 2 going to newyork--- area 0 3 going to dayton----- area 0 I have ospf configured as...
I think we're still missing a piece of your puzzle. Can you be more specific as to where the data is going? Are london, newyork and dayton connected to one...
Yes they are ... Dayton is my primary hub and New york a secandory one and moreover london is connected with both of these also . ... ===== Raman Preet Bajaj ...
Well, OSPF should handle this with no problem and with just the basic configuration. But, you are confusing "load balancing" with "redundancy, or route ...
Hi, I have the following doubt regarding OSPF. My network is more or less as the diagram below: http://users.trendnet.com.br/nelson/network.jpg Router2 has a...
Raman That's a simple issue,try using "ip ospf cost 1" on the primary link and "ip ospf cost 2 (or greater)" for the back up link. If this doesn't work then I...
Hi! I'm just new at routers and I would like to know how CEF behaves...How is it implemented and can I load Balance with CEF?...Hope to hear from you guys...
Hi Marcio, If there are two paths to reach a destination then ospf chooses the one with lower cost to the destination.This is the rason that your traffic is...
You should be able to find everything you need at the following link: http://www.cisco.com/en/US/tech/tk827/tk831/tk102/tech_protocol_home.html I would pay...
Hi, The cost of the paths is already set up that way. But my problem is that the router with the 128k link, when sending trafic to the networks in Area1, uses...
Can we see the OSPF and appropriate interface configs for the area boundary routers? router1 and router2. Tim ... __________________________________ Do you...
Shouldn't you have three areas in this scenario? Area0-1-2.. Area 0 being your backbone area? Router's 1 and 2 need to be listed as ABR's with full knowledge...
Dear Cisco_CCIE Group , How ar u hope every body doing well ....!!? Did any on have idea about the command netstat -a usually it used in
DOS prompt .....
Nasir S.Saeid
nsaeid.c@...
Sep 5, 2004 4:32 pm
2609
you can use nbtstat to tshoot netbios issues. ... __________________________________ Do you Yahoo!? New and Improved Yahoo! Mail - 100MB free storage! ...
hello friends, I have two equal parallel active links one Mb each for internet from the same ISP in one 3660 router. One is on the ADSL card and the other is...
Are you looking for outbound and Inbound load balancing? Is your problem with outbound or inbound traffic? If you are accessing sights that are located on...
Sandeep, you can configure load balancing for your outbound traffic, but the ISP is going to control routing coming back. What are they doing on thier end? ...
hi, any one help me to download ios in pix 515 to tftp server, and how to view the flash file name.i tried write net but i can downloaded only 6kb file. ...
I am CURRENTLY WORKING ON ALCATEL 4400 PABX. i require assitance and/or materials on how to become AQFP(Alcatel Qualified Field Professiuonal). Currently , i...
Hi, You cannot take the backup of Pix IOS on TFTP Server. This is what i had heard b4 and also had tried but was not successful. If u get the procedure to take...
Hello Nasir, Since you are using a windows workstation, why not just click on the Network Neighborhood icon, and see what you have? Otherwise, use the netstat...
Hi, I would suggest that you get hold of a person working with Alcatel for certifications, because they got access to lots of materials, which is difficult to...
Does anyone have the default and maximum configurable mtu sizes for CISCO interfaces with the protocol types listed below? What's listed below is for Juniper....
Hello everybody, I'm currently a Network Admin at a company with no Cisco. I have my CCNP and am interested in side work. Does anyone need some help ...
Hey Michael, I've seen all these in a cisco book before. And I hate to say this to you...but...www.cisco.com...:>) Regards, Henry ... From: "Michael Younts"...
please can someone help me with this problem this is the scenary.. I have 3 routers and have in router 2 R2 loopback L0 and L1, in R3 loopback
L1 R2L0 IP...
Michael default mtu sizes are not vendor specific. Same list is applicable to Cisco. -Raman ... __________________________________ Do you Yahoo!? New and...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
