dude,,, its traffic shaping ,, QOS. read Cisco Press BCMSN book's QOS chapter, u ll come to know. or search on www.cisco.com/univercd see, with the help of...
Dude,, the way i see it. Which would be the most reliable interface on ur router ?? u would like to form neighborship with the interface which would never go ...
dude, u will find all the IOS on cisco's website. just check it out, u might be missing out the link. go to cisco.com,, in that go to the downloads section. ...
Hi all, Can any one, help me getting a soln.. Juzt take a look at the network diagram attached. all the clients have to cross the firewall for internet access,...
dude, saw people giving lot of opinions about the same. its all about the mindset. wat u wanna become. technology is my passion, so i am into it. are u ? the ...
Dear SundarBhai, For the network attached you have the firewall, router ethernet port and the switch on the same network. So the packets will travel ...
Hi, Sundar.R if you get any solution then ok, if not , kindly send to me network diagram and show tech of firewall and router. i think its access list and nat...
Guys, I am getting this output error and collision on a 2610 router. I have tried changing the Dell switch and using a cisco switch on the interface connecting...
check (change)The cable and hard code speed and duplex ... __________________________________________________ Do You Yahoo!? Tired of spam? Yahoo! Mail has...
Hi, Can anybody help me with a document to design and implement such a migration Process. Thanks Lodh ... How low will we go? Check out Yahoo! Messenger’s...
i am praveen.i have a small doubt abot the voip packet.can anyone please give me suggestion how will u identify the voip packets if the voip is not configured....
hmm.. I'd definity be more worried by 764 lost carrier, 0 no carrier... check cabling? also make sure your switch is locked to the rate that your 2160 is set...
Dear Mr. Hares your problem may be due to half-duplex operation of ur ethernet port u better use the full duplex mode or auto negotiation operation. Regards, ...
you can configure dialer watch group to track VSAT network as soon as VSAT n/w will become unavailable youre isdn will fire can you provide config? ... -- ...
Pravin Patil
pravin.ccie@...
Apr 15, 2006 2:04 pm
4488
you need to give different security Laval in pix for interface Ethernet1.1(98) and interface Ethernet1.2 (99) and give apply ACL from E1.1 to E1.2 i think you...
Pravin Patil
pravin.ccie@...
Apr 15, 2006 2:04 pm
4489
you have to do some change in n/w design. do the change as follows: 1)Firewall will be your central device 2) connect internet to outside port 3) connect...
Pravin Patil
pravin.ccie@...
Apr 15, 2006 2:14 pm
4490
well, u hv to recall the concept of Quality of Service(QoS)..... in which one of the field of IP Pakcket ie. ToS(Type of Service) had given a value of 5 to...
Hello, I am preparing for my R&S lab, and I was just curious as to how others are currently studying or have studied for this test. I am baffled by all of the...
Hello Networkers ! Back again Could anybody please please let me know the MPLS supporting ios images for 2500 and 2610 series platform routers ! Site is at...
Hi Guys, Required support and guidance from you all. Actually, I am preparing for CCIE lab.I am planning to setup my CCIE home lab; can you give me details of...
Hi all, port1 --------- ... port2 | | ... I have problem in routing calls through AS 5300. Objective is to route all the call with any destination number...
Kal, Cisco IOS can have logical interfaces like loopback other than physical interface that you have like ethernet, serial etc. The magic of loopback interface...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
