Dear All, I need your help regarding Cisco Express 500 Switch . I need to know the mac-address of systems connected in Each port of the Switch ?? .ie the...
Dear ALL can any body suggest me how can i install a new IOS in cisco837 router. i already have tried to isntall using TFTP_DNLD & Xmodem. but find no results....
Well in my opinion I would never do this. You have different delays on the two lines. This particularly true with the segmentation and reassembly (SAR) of...
Dears, I have to VSAT links from different ISPs. I want to configure the cisco routers for Link load balancing. I attached the files: BGP-HSRP.doc= Draft...
Really depends on your design requirements. If it is backbone only then Juniper is good competition. Required features will drive design. For instance...
no MPLS for 2500. Even no MPLS for 2610 as well, only multi-VRF CE is supported on 2610. who is this customer in mumbai ????? -Santanu Network Consultant,...
hi group, i have cisco L3 switch and 2 provaiders. And want to configure that if primary provaider gose down I can use secondary one. I had cisco router and I...
hii, this is praveen.is there any way to chage the voip packet to data packets. how to monitor those packets. example- 2 routers connected to each other the...
Dear All, Is there is any way to Configure PIX or Router to allow FTP PASV mode . I configured my router with the following ACL ,everythiing is working except...
Dear all , We are trying to enable do1q encap on Fastethernet of 3460 Router with IOS c3640-is-mz.122-32.bin ! interface FastEthernet0/1.1 encapsulation dot1Q...
hello well,the acutal size of VoIP packet is 40 bytes(20 IP+ 8 UDP +12 RTP).... now with the help of cRTP(compression RTP) command,u can reduced the size of...
Dear Kris, What's the command for configuring FastEthernet 0/1 interface toi be trunk . Regards, Haris kristiadi_himawan <no_reply@yahoogroups.com> wrote: Hi...
Yes exactly, My friend did u put the pc directly to the Fastethernet ? dot1q is the Vlan encapsulation for trunk interfaces, not access interfaces (which in...
Here is what is needed for Passive FTP to work. Good Luck FTP server's port 21 from anywhere (Client initiates connection) FTP server's port 21 to ports > 1023...
4500 series is a switch Clayton Brown <aclaybrown@...> wrote: Hello Can the 4500 series router support mpls? If so what ios do I need. clay ... YAHOO!...
sucessor is the primary route eigrp will take and it is in the routing table vs. feasible successor it is a back-up route that chills in the topology table and...
Hi All I am new on group, My company is decided to buy two 4506 switch and 2960*10 switch. From each 2960 switch one link is connected to 4506-1 and 4506-2. ...
Hi Sara i agree. But the best equipment for MPLS implementation is Juniper.(experienced it myself) Atif Ashfaq pratheepan sarasanandam <srptheepan@...>...
Hi Redundant Topology. Atif Ashfaq DHANANJAY <d_awachat@...> wrote: Hi All I am new on group, My company is decided to buy two 4506 switch and 2960*10...
Dear friends, can i configure one of my routers as a NTP server for another routers in my EIGRP network ? i have 8 cat6500 with ios image 12.2(17d)sxb9 in my...
Hello I wrote for information on mpls and cisco 4500 routers. I was not talking about a switch. I can't seem to find enough information. I want to configure ...
Hi Everybody, I am planning to take my written paper shortly, I have gone thru Jeff Doyle (I and II ), LAN Switching and currently reading Sam Halibi. So What...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
