hi Can you guide me how to configureVPN between cisco pix and Sonicwall.?i have done VPN for Cisco but it;s with static ip,Now the Cisco Pix has having the...
hi i'm regular user of broadband internet user in my pc via dlink swith.] In the mean time my pc not connected internet. switch can be damage no link,no...
Dear Mr Rahman Your problem is not clear to me, Let me know 1) Your SWITCH's power is ON ( ? ) 2) Supplied line from your ISP is OK. ( ? ) 3) If last 1 and 2...
Hi, I have a VoIP connection between 3 sites. The sites are connected through MPLS network. In every site there is a Siemens PBX connected to a Cisco 2801...
I have two locations El Segundo and Kallang connected through MPLS network and we have a back up T1 circuit between El Segundo and Kallang. The office in...
No changes needed if you are using different IP addresses. If you are planing to use the same addressing. I think that you should do a turn off and on. I...
Hi 1. How do u check trafiic load on cisco 3750 switch, if the switch is connected to servers and which IOS command do u use? 2. When I checked the interface...
It means collisions. i.e. bad cable, or a wrong speed configured between sw and host. The only tool you have to check load balance is sh interface. and clear...
Hi ALL Can anybody tell me what is the voltage to be checked at the input for ISDN Connectivity ( the line voltage that comes from MTNL/BSNL to modem ) for ...
Hi, voltage should be between 95V to 110V for best performance swapnil ... From: gowri <gowri8@...> To: Cisco_CCIE_Lab@yahoogroups.com Sent: Tuesday, 1...
its BRI or PRI .. but in both cases its same I suppose .. it was 95 V DC .. when I did worked on it last .. I guess its same till now .. Its like 5 years ago...
Hi gowri Normal voltage shall be 110 volts but practically the voltage may be between 104 to 105 at your modem end for best data transfer. Gopal S gowri...
The voltage that passes through the pair comes from the NE device kept at BSNL Switch room and it is DC volt. Generally it measures from 96-97 volt to 105 volt...
Any body has Configured CISCO PIX VPN on Dynamic IP.?as in PIx,it;s allowed to enter only IP Address..so can you give some focus if you have idea for this.? ...
Dear Group Members I need to design Video calls & conference solution to my company. Idea is 10 location with two ip phones with VT advantage for each location...
HI, Hy, if I understend correctly, the configuration of interfaces to dynamic ip is: ip address outside dhcp ip address inside 1.1.1.1 255.255.255.0 I hope I...
Hi Can anybody tell me the tools for monitoring the network traffic and where and how do I purchase them? Thanks a lot in advance, Waiting for your mail, ...
hi, Solarwinds is the monitoring software, where you can monitor network traffic. Shibi Ali <shibi.alikunju@...> wrote: Hi Can anybody tell me the tools...
Dear Group Members I need to design Video calls & conference solution to my company. Idea is 10 location with two ip phones with VT advantage for each location...
Get a CCVP. My sugestion is if you dont know how to design it, dont design it. It will take you more time than it is needed if you dont know where to start . ...
Hi pradeepan, Make a drawing/chart of your project first then spit the events. Ask sugestions for each event. Finally you may get the answer. SubiyanGopal ...
Hi SubiyanGopal & Adrian Lopez Thank you very much your reply. This is my request... Head office & 10 branch officers. Branch offices VT advantage with IP...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
