Hi Long time no post. I have moved back on across the pond back to the UK. I have dug out my DIO after a long period of non use. On checking it over, I note...
Just found this group yesterday. I just received my second hand DI/O the other day. Got a good deal on Audiogon on one with the Bolder Mensa Mods and Bolder ...
Welcome. The traffic on this list died down long ago but I found several weeks worth of reading in the archives. An excellent condensation of the list...
not too surprising you woulkd get noise at the 48 & 96 setting, as this isn't what a standard cd opreates on 44.1, 88.2 & sync should all work fine. if your...
Hey...long time no hear. The Arcam is probably AC coupled at its input so that a little offset is not a big deal. There are very few amplifiers which are...
I am new to the group and I can't seem to find if this has been implemented before but I would like to upgrade U1 with the AD8620. As there are no SOIC8 to...
1. Yes, you will need two AD8620's to replace one TL074. 2. I have not looked at the AD8620 datasheet. However, let's assume that it has the standard dual...
In order avoid Digikey charges and to fill out my upgrade BOM I need the following materials: Caps (3) Panasonic NHG 3300uf 16V Caps (4) Panasonic FC 680uf 25V...
... Yes! Quality ALWAYS matters. < grin > ... Bits are bits. In theory all the same, but some cheap or poor designs can introduce more errors. Remember also,...
Digital output is all the same.... Mark <mmarussich@...> wrote: Does the quality of the card matter or is digital output all the same? SPONSORED LINKS ...
Hi all what gives the best result when listening to CD ? 44khz , 88khz or ext. sync ? Alain ... avast! Antivirus: Outbound message clean. Virus Database...
With my DIO and Squeezebox combo, the 88.2 has proven better. My external sync is a little flakey. I think that the 88.2 sounds a bit better though. -MA...
Hi for me , 88khz gives a sweet and nice sound but i think that the DIO upsampling stage is not of the best quality , so i'm now trying 44khz Alain ... avast!...
Can anyone recommend a good place to purchase the RCA sockets with the nut on the exterior of the chassis? Preferably in Australia, but the States should be...
Hi, Scroll down the page at this website. They have them here in Pennsylvania, USA. http://www.hndme.com/storecardasrcafemale.html Regards, Bob ... From:...
Percy Audio is in the US too. See page 3 of their pdf for Vampire brand RCA with an external nut at http://www.percyaudio.com/Catalog.pdf Jim L'Hommedieu USA...
A few weeks back I changed the opamp, diodes, and all power caps except the two smallest (closest to the tube socket). The unit worked fine after these mods. ...
Unfortunately I will have to state the obvious. You probably have a lifted trace somewhere. Check all of your solder joins and the pins on the op-amp chip, and...
A "lifted trace" means it's been burned up and no longer conducts. It's open. When I was using a $10 Radio Shack iron, I had that. In addition, there were...
Thanks. You were right on the money. I had lifted a trace between C18 and R7. It's now repaired, and singing like an angel!! ... addition, ... iron worked ......
For this type of thing, i usually need to see the pinout diagrams (get the data sheets and place side by side) and draw out the circuits to keep track of what...
Here's another option: G. Bronn recommended replacing U1 with two Burr-Brown INA103. Best of all, he put general instructions including part numbers on the...
I'm using a NAD C 521BEE as a transport. About 70% of the time, I have to switch the ART DI/O off for a few seconds when I switch CD's, otherwise it doesn't...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
