Right, i've found the one for me!!..... Expensive, yes. But not as expensive as i expected. Banner D10DNFP, (up to 5Khz switching!) all singing and dancing,...
oh, cool, thanks. sorry, I do feel like a bit of an a** with all that fuss, but there's only a few weeks left where it'll be of practical use for me. ... A ...
can I come over your place and hang out? I had a 79 aspen hard tail. we welded the rear suspension solid and drove it around, it lasted about a day, the axle...
...lol...Sure Chris come on over!, I'll have to send you some pics someday Jim __________________________________ Do you Yahoo!? Win a $20,000 Career Makeover...
http://home.covad.net/~jmaechtlen/cars.htm I do have a turbo for it, of course... but first, I just want to get it rolling under it's own power! jay ... ...
If you think things are bad in the US, just think how bad we Brits feel. We used to be number 2 to the US in volume of cars produced and exported. That all...
Imagine that. The first engine change that I did was a 73 Vega Kammback. Dad bought the sleeved short block and I did everything else. The neighbor claimed...
Ron & Mary Ohler
r-m-ohler@...
May 2, 2004 4:10 am
18068
iniyavan, Do you know anyone who makes cables to connect LCD panels to single board computers? Do you have a good source for data sheets, drivers, bios ...
Hi Just a short note to let you know that I couldn't get a second electric motor to double up my blower starter power- remember, we couldn't get quite the revs...
I had a V8 vega wagon. You could see the gap between the door and the roof change wheh it hit 2nd gear. I've heard of people putting enough power in those...
I was a lot older when I started- Swapped a Dynaflow at age 18 or so-without a trans jack, out of and back into my '56 Century. That trans was a heavy dog! ...
yes i'm interested ,so will start the bidding war !! not as big as i would like ,but would fit on my project if i get it !!! i'm really after a bigger scary...
Hey John, I'm impressed at your P4s. I didn't think that they would get that high, it must be a fairly efficient turbo-compressor setup. What kind of boost are...
... using ... around. ... considering the small amount of computing power needed for the actual jet control, what about using either a Palm-type device or an...
I apologize if this is a repeat performance but I tried this post earlier and it didn't seem to 'take'. We (my teenage son and I) are new to the forum and wish...
We're new and have been watching and using this forum for advice. Our turbine project is just recently up and running (within the last week) and we're very...
Hi Here in oz I found a frequency counter kit that is quite good. The kit comes with every thing but a pick up. It is for AU$70 and messures up to 6KHz. It has...
From: "carlisle_99" <carlisle_99@...> ... It sounds like a good project, congrats on getting it going on your own. If it's running with good temperatures...
Went into mad scientist mode over the weekend and now I have a working tacho...goes to 99,999 rpm, lcd readout...and made it for about £12. Now just need to...
Sounds like a bargain!....how did ya build, and more importantly test it?? painted spinning disk (or grinding wheel) is always a good method! Nick ... are ... ...
can you tell me the computer you want to connect to? what type of lcd you want (how many line display etc..) i actually use a single board computer built by...
hi jay the hardware stuff is steep due to 1. i have some really good p4 boards and computers in scrap(got off a fire insurance sale) 2. my aim is to make a...
Actually I use Qbasic quite a bit. The low overhead and direct port access is great. I have also done some I/O in Visual basic, but you'll have to download a...
I'd be interested in seeing the schematics... Eric iniyavan karthik <iniyavan_karthik@...> wrote: can you tell me the computer you want to connect to? ...
... Even though you're running it as a gas turbine, it's still at heart a turbocharger, and turbochargers are designed to run on the same oil as the vehicle it...
Hi Ben Under "normal" conditions the 12psigauge total pressure in the jetpipe is at P2 of 45psi gauge (4:1 PR) and a TIT I'd better not mention , but static...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
