Hi Nate, The pumpkin is great! Picture saved on my comp. Russ ... what one ... _http://i20.photobucket.com/albums/b209/Stormtrooper154/Halloween.jpg_ ... ...
hi ,had a problem b4 getting some 4.5" internal hose ,but the good old USA have sorted it!! just ordered some short lengths ,3,3.5 and 4" long pieces. not...
I have a question about V-band clamps. I cannot find the actueal one for my turbocharger but I am wondering if this one on ebay will work Item number:...
Mark a line with a felt pen in about the same position on both wheels; that way they can be put back with the same orientation. If the assembly was balanced...
Hi guys, Well, it isn't quite finished yet, but the guys at work wanted to see pics. So while I was at it, I put some in the photo section in "Rick's Toy"....
Hi Rick Loooking good , nice finish :-)) Cheers John ... From: "Rick Reid" <kq6wr@...> To: <DIYGasTurbines@yahoogroups.com> Sent: Wednesday, November...
Hi Rick, Vey nice work! I hope that my second combustor looks half as good as yours does. I can't wait to see her run. Keep up the great work. Russ ... see ...
First of all i am new here and would like to say hello to all of you. If my english is not correct at all times, please excuse me. (Glad to have found a group...
First things first, please read newbie help from this group files section. That'll give an answer to much of your questions. Then the answer to your question:...
hi all ,is there a meet at bov at the end of november? i have my own van now so i can go this time.also i have a kart chassis to give away if any one wants...
Very Nice Rick. Might i just say though.... i don't much care for that 'springer' type inducer cover!. those sharp edges could cause problems when that big...
There used to be a guy on ebay who sold a pre-fabricated jet engine kit, used a VT50 turbocharger i believe. Well i can't find it anymore, seems to not be...
Thanks for the compliments, Russ, Nick and John. Question for you, Nick. Are you referring to the not very tapered edge right at the inducer inlet? I looked...
Well I appear to be stuck on figuring out what kind of fuel valve I should use. I just went through the files section again to try and figure out what kind of...
Hi John, A beaver on speed would have a hard time keeping up with you! That's some seriously funky piece of kit and looks good to go! Have you fired her up...
Hi John, Interesting looking contraption that you have there. Is that a sprocket at the front end of the PJ? Can't tell for sure. Rick ... [Non-text portions...
Hi Devin, I'm not sure what you mean by "fuel valve". Are you referring to the fuel nozzle? Rick ... [Non-text portions of this message have been removed]...
Yes, I was my apologies. As I was writing my question I also had another website open with ball valves on it. Just shows I can't multitask tonight. As both...
Hi Devin, Oil nozzles are good for liquid fuel. Unfortunately the threads are a pain, they're 9/16 24tpi ( UNEF ), I couldn't find a suitable female thread to...
From an earlier post: Mcmaster.com sells inexpensive mist nozzles. 4 to 5 bucks each. And available in useful sizes. The things are stamped with the "Hago"...
Thanks sal, you said it was good for liquid fuels. Does that mean it would work good for propane? Or should I just get a small steel tube and weld one end...
Thanks sal, you said it was good for liquid fuels. Does that mean it would work good for propane? Or should I just get a small steel tube and weld one end...
Hi John, You are a %*$*%( madman! I love it. Looks like a doomsday machine or something for attacking unruly viking hordes. (my appologies in advance to the...
Hi Mike, All of the information you need to construct a workable engine can be found in the files section. Read eveything there, most importantly the rules of...
Hi All There are only 10 days till the Florida Jet Fest. Any that will be coming please go to the wed site and register at http://www.floridajetfest.com/ Thank...
Welcome Mike, I am new here as well. I find there is a wealth of info in the files section. I have found that the calculations sections have taken several...
Hi Devin, I have no experience of using propane, you'll have to ask those more in the know! ;o) As for the thread, I'm using BSP threads so I got a 30mm long...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
