Hi, It doesn't take that much heat to boil freon. Freon isn't particulary corrosive and there are very good lube oils that are compatable with freon. I'd never...
Its not a free power turbine. A free power turbine is just that, a hot side turbine that rotates on a seperate shaft that has no mechanical connectings to the...
LOL, man, I think I learned everything I need to know about power steering pumps. I had not idea they could be so complicated. ... [Non-text portions of this...
Hi all, Over the weekend I got my turbo 'shopping list' sorted and decided to buy a few things. I went out and got some steel locally, bought a few things...
I am working on my combustor ring drawings and am planning on using 1/4"-20 Socket Cap bolts with 1/4" SS nuts welded onto the ring. When machining the holes...
... I to got the same message from McMaster-Carr,have a look at this site www.tecpro.com.au I purchase my shurflo pump from pumpagents.com Mark.. ... to buy...
I have just recieved my turbo and I removed the compressor housing. Do I have to put it back on the same way it came off or can I spin it so that the comp....
Hi, Got my flame tube drilled out tonight. Took about 2 hours, bought news titanium bits especially :) made life much easier! Consists of 30 (31 for overlap...
hello all this thing is for sell on ebay.the guy selling it said over and over that it is a free shaft.looking at the photos i dont think it is. Matt thinks...
Im affraid i cannot provide any meaningfull input, as if no experience or knawledge, i am wondering... If somebody asks the seller to try and turn the output...
Does he at least have a manual for the engine? If not, it'll make doing anything with it a bit difficult. If he does have the manual, it would certainly state...
... i have looked on the internet for imfo,not a thing to be found.i think it is a free power turbine but the free power unit is missing.look at this. ...
... I googled for "JFS-190" and got a lot of hits concerning a fuel supply/control problem. I think it's important to be knowledgeable about what you're...
Hi Sal LOL....I'm addickted to her , such a sad case :-(( After painting her nose black and white this morning , I caressed her into action , slow and easy...
... I kinda hate to become a teacher, for basic machining processes--but this one is just crying for an answer. Yes--a 1/4-inch drill will create the correct...
Hi Matt, I thought the same but then I read this in the listing: "(FREE shaft HP--so it can be used in a go-kart or boat project-- allowing total stoppage of...
Hi John, This is going to have to be issued with a restricted certification now, suitable for adults only ;) Karl VK3TLY ... From: John WALLIS (Racketmotorman)...
Thank you Jon for your reply. Its also nice to talk with another JON (not that there is anything wrong with Johns) Sincerely, Jon ... housing. ... it so...
I enter my inducer diameter and it calculated everything. Is it supposed to give me the number of holes to be drilled in each of the three zones? It just reads...
I enter my inducer diameter and it calculated everything. Is it supposed to give me the number of holes to be drilled in each of the three zones? It just reads...
Hi Karl LOL.......... Sal did say she was a "temptress", a fine figure of a girl , who demands respect, "in the morning" ;-)) Kinda "improves??" on my...
Hi Jon I just had a try on Jetspecs and you might need to just "play around" with it a bit . The same 1#nf came up, but I on hitting "calculate flametube" it...
Can't wait to see the new videos:) ... From: John WALLIS (Racketmotorman) To: DIYGasTurbines@yahoogroups.com Sent: Sunday, December 02, 2007 2:03 PM Subject:...
Hi Jon What diameter is your compressor wheels inducer ?? Cheers John ... From: Jon A. To: DIYGasTurbines@yahoogroups.com Sent: Sunday, December 02, 2007 2:01...
Hi Karl They're definately be G Rated :-)) ..............but in colour . Cheers John ... From: Karl Church To: DIYGasTurbines@yahoogroups.com Sent: Sunday,...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
