... that the ... appears ... next Darks ... leakage ... rather than ... Bob, I hope that does it. I have the same problem, and I always use the nose cap on my...
... previously ... be ... subtracting ... I haven't had a chance to check it out under actual imaging conditions as the clouds seem to think they own the skies...
Hello Bob, I've not used Envisage in a while, But it doesn't look like its a stacking issue. The smaller spots, are likely from a bad dark sub. The large from...
I got my DSI last fall from an outfit that was called Optical Overstock. The Autostar disk was so warped it would not read. I fanally got a replacement. And...
... You might try putting an aperture mask over the objective of your ETX125 for daylight imaging. The DSI is sensitive enough to give you totally overexposed...
Sorry I confused my self. you're right. I tried to parfocal and thats when I couldn't focus the dsi. i.e. no recognizeable images. I'll try your...
Sorry, when I mentioned earlier that you could take out the dark frames after imaging I didn't know that you didn't save all of your subs. I believe darks...
I recently obtained a Meade Deep Star Imager PRO to use with my Meade LXD75 SN-10AT. After sighting in my target with the telescope optics, I installed and...
I'm not familiar with an SN-10AT, but I assume it must be a Newtonian from your description of focusing problems. On all Newt's you will have to get a low...
Thank you for this information. I removed the extension and it looks like it should work. Will try to post a picture as soon as the weather allows. ... back...
... I haven't seen the LXD75 SN10 in the flesh, but the instruction manual on Meade's web site tells how to set up a schmidt-newtonian for photography with a...
Hey Bud, Appears you are much more correct than I was about this. I should have figured out what SN meant! Doh! Moving the mirror most likely would not be a...
Hi, I replaced my Meade SN-10 plastic focuser with a Moonlite Crayford CR-1 with motor focus. This allows me to uses a focal reducer as well and I have all the...
Hi Folks, I'm new to the group. I just purchased a used Meade DSI C and Mogg adapter to use with Canon lenses. I've got everything set-up, etc. I haven't taken...
Has anyone successfully guided a C8 with a DSI I or II using Envisage guiding program? I plugged in my R-232 adapter into the autoguiding port and the scope...
June 2008 Issue (Volume 4, Issue 3) In this issue you'll find: * Remote Control Astronomy Renowned imager R Jay GaBany covers remote imaging options. * Bench...
I'm not an expert on this, but I don't think it would work. You could try software that understands both the DSI and C8. Something like PHD from Stark Labs ...
Mike, Envisage is not a guding program. Try PHD. TSP, what a place to learn. There should be others around that can assist.Clear skies, Rodney Owens ...
One thing that is true is that the DB-9 to phone plug adapter supplied with the DSI or DSI Pro only works with the Meade controller. It will never work with...
i have had to redo my computer and installed autostar suit 5.0 and pluged in dsi and lpi and on both I could not find the drivers. Can someone point me in the...
Did you download Envisage 7.05 and install it? Eagle Station One You must believe in yourself. Doing so will inspire others to believe in you too. ...
Everybody must be taking a little break, due to floods, quakes, tornados, heat n' humidity, blizzards, and all that other wonderful weather phenomena that tend...
... Very nice Tim, I also lucked out last night, a lull between thunder storms, I also hit M27: http://www.floridakiteboarder.com/astro/dumbbell-2.jpg DSI-C,...
... Mike, envisage is no good for autoguiding in my opinion. I used it on my LX90 and it was terrible. 3 pixel corrections constantly. It was actually WORSE...
Thanks Tom, I seen your photo in the other DSI forum, nice job on the framing, looks like the color cam does a pretty good job... My M27 shot was my first...
Hi Tim, I started with an LX90 but could not get decent autoguiding results with envisage through the serial port (using the autostar). I had trouble...
I have the celestron neximage camera and have done a number of planet shots. However I would like to get into deepsky imaging and I am thinking of purchasing...
Hi, you are fine with what you have for starting out. You can easily image globulars, some galaxies and nebulae in alt/az mode. The trick is to wait until...
Thank you, it all sounds rather daunting. It looks like I will be researching for awhile. I want a lot of utility and universal items at a cheap price. How...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
