G'day - I'm working for a regional museum in Central Queensland and would like some advice on a software application that would provide thumbnails for a large...
... Hi Ted Welcome, it's good to find another Queenslander here! I am happy with IMatch -- see www.photools.com -- but your requirements may be different from...
Hello. I've used piezography Icc my old epson 1200 and ,exept the high price of the inks, everythings worked fine and the prints are beautiful. Now, I'm...
... Will Many of our images are of the 10 to 12 inch by 25 to 40 inch. I presume I could cut these sheets as needed, perhaps a couple of days ahead. Do they...
Phil, The only reason my method works for me is that the roll is 17 "" wide and I cut it to 13" strips. In reality, the only reason I need to flatten mine...
... rolls for this printer? ... Have you looked at Hawk Mountain papers? I sent for their swatch book (free) and found what I was looking for with HM. Check...
... I will look into that. Not having the time to check out all the many papers available, I tend to stick with a slect few and mainly Epson. Enhanced matte is...
Yes, I saw that rip but Ididn't see any profile for epson 1200 do you think it drives my epson 1200? i'll use it on a intel based macbook Thank you. sari ... ...
Sari, ... The MIS UT-FS and FSN inks are PiezoBW clone inks. I've never had a 1200. There may be some 1200 curves, etc. out there for the old, original MIS VM...
Premier Art Hot Press 205 (see http://www.atlex.com/premier/fine-art-205.htm) is one of my favorite matte papers, in part because it is OBA-free, does well on...
... I also rinse the ink off the outlet with a syringe I keep full of water. Then I tape the outlet. For really long storage I tape the air inlet -- only...
Dave, ... When you give up on Lyson, consider the MIS FS or FSN inks. I don't have a 2000P, but a local loaned me one to set up with these inks, and it turned...
Hi, I'm a longtime lurker and occasional poster from New Zealand. I do apologise for posting a message not directly related to printing, but a few weeks back I...
Greatly enjoyed your entire site, especially the portraits. Navigation and layout was clean and easy. Perhaps too many of the town pictures and editing to a...
A while back I reported on tests of various coatings for Innova F- Type Gloss Ultrasmooth paper. The prints were made on an Epson 2400 with stock Epson K3...
Hi, Intresting information. I liked to ask you in what way you spry your prints with primmer Art sheild. I am looking for the best sulution how to spry 105...
Hi Richard, Your statement about Miles is a bit extreme, but I agree. Counting all LPs and CDs I have of him, there must be around 100. (This is without...
Joachim, I am using the regular 400 ml aerosol spray cans. I have not sprayed prints the size you mentioned – only done 13”x19” to date. I place the ...
Yes, the UT-3D Silver Rag curves use the M and C to make the 100% black. The black spot, usually occupied by Eboni, is not used. Paul www.PaulRoark.com...
Okay, you've probably had this one a zillion times already. Here's zillion-and-one: I'm in the market for a good photo printer. I'd like to spend less than...
Hello All, If anyone is in the LA area I welcome you to check out; http://www.faheykleingallery.com/featured_artists/laita/laita_frames.htm Mark Laita has a...
... I'd recommend it because it does a very good job with both color and bw right out of the box. It has long lasting pigment inks, and MIS K4 inks work in...
Hello Ned, ... Some other thoughts in addition to everything Peter said abut the 2400 (which I 2nd). It's normal retail cost is $849 so unless you find a sale...
