for information, I saw on the site of the script example we used the attribute page_order, the one doesn't function here well it is preferable to use the value...
I look for to win of the time a person that to writing this type of script to change the bus color help for designer to read schematic - read conts.bc file -...
The diff pair consists of 2 50 ohm striplines (gnd planes and sig between) to form a 100 ohm pair. What are the attributes to do this? if any exist. And does...
Hi, ... 100 ohm differential pair is different than two 50 ohm "striplines", so I'm not sure what you mean here. ... Anyway, in DxD you assign an attached...
I had a schematic that was entered with a grid spacing of 10 and I had to changed it to 20. I tried entering snap on the command line and snap all the...
Austin, I disagree with your comment on the NC attributes. In many cases, the manufacturer of an IC will note that certain pins SHOULD NOT BE CONNECTED to...
Hi Dan, ... I understand that, and didn't suggest otherwise. ... That's subjective as to what is "best". What I do is put the NC pins on the symbol (and label...
Thanks for the input on the NC. It seems I took a Xilinx ml401 and tried it on pads 2000 then did a check. It wanted to see the NC pins somewhere and I think...
Hi! We do variant schematics. Right now, the schematic engineer has to start the DxVariant manager, generae the BOM report and then call a tool from us to...
What you need to do is look on a schematic for a part marked as a variant and find the attribute name that marks the part as a variant. Then modify your...
... variant ... modify ... I looked very hard but I didn't find any. The only difference that showed up was that when I created a variant schematic, the parts...
I just ran XREF with new attribute visibility set to "Invisible". So all of the XREF attributes are invisible, which is obviously not what I wanted. Is there...
Thanks, Ivor. ... So ... what I ... ______________________________________________________________________ _ ... intended solely for the use of the individual...
there is a command for turning attributes visible and it does accept wildcards just look under commands under help ... -- "We are all born ignorant, but one...
FYI To make pins visible after using the symbols wizard just edit the symbol just created in word pad. Change "0 #" to "3 #" for the entire files and the pins...
Thanks, Les. A colleague also informed me that the command that does this is "avvis xref" where "avvis" means "Attribute Value Visible" and "xref" is the...
As someone that started with Viewlogic ViewDraw in Dos on the AT machines learning the commands was a necessity. Unfortunately each Rev and update seems to...
Which commands were removed? It is also possible to define your own commands through scripting, if you're so inclined. John ________________________________ ...
There may be hope for Vista users. While this is a cartoon I have found they have a good knowledge of what is going on with Microsoft. Can anyone confirm it ...
I had to clean house 5 years ago and throw out the gray Viewlogic and the Black Viewlogic Binders I do remember being up set when Viewlogic left the Dos domain...
You also used to be able to expand A[0:31] on ANYTHING that was, obviously, text. Now, it's limited to nets. I used to use it for text inside my symbols, or...
Expansion should work on any label or attribute value - do you mean through the command line you can no longer expand? John ________________________________ ...
Hi John, I mean in the GIU. Pin numbers do expand...I'm going to guess that got fixed somewhere along the line. But text does not. It used to in the DOS ...
Help-I have been with Dx Designer since it was View Draw. I am now with a company that only uses Power Logic. My Question is "Is there a software out there...
Hi, it could be even more simply: in the command line of dxdesigner enter avvis ATTRIBUTE_NAME to make attributes visible on the sheet it also works with...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
