Most home-built EDM spark generators so far are based on R-C circuit. Does anyone know of any available resources, circuit diagrams, etc. for the construction...
... To my knowledge there is no published circuits of the type I think you are looking for. Look at the thread "Your Wire EDM" on the Homebrew_PCB yahoo group,...
--It has been my experience that trying to find such a set of plans is difficult they are few and far between. I am at the present time work on a design for a...
It has been my experience that trying to find such a set of plans is few and far between. I am at the present time work on a design for a pulse unit but it is...
... From: Ben Fleming To: EDMHomeBuilders@yahoogroups.com Sent: Monday, October 03, 2005 11:08 Subject: [EDMHomeBuilders] EDM Pulse Design plans?? It has been...
... I expect you have seen: http://freepatentsonline.com/4382168.html and then gone on to reference patents that refer to this one, etc, etc. A lot of work...
I bought it a few years ago, and while everything in it is available on line, there's too much OTHER stuff that is NOT applicable to wade through. I've done...
... Normally the motors only have the rpm listed, and gearboxes are just expressed as ratios. Look up the specific motor page, then work it out. Steve...
... etc. ... You ... The ... Rag is a good word. this pubulication has nothing for the home shop. some ads from Charmilles and others, but absolutly no...
... One note on patents. They are written to lock in a thing and to also not reveal a thing. Many hours are spend on special wording that will create a...
... to list ... Is you know the voltage, then power it from a good voltage source and use a watch and count the RPM. I think the window is pretty big for ...
--I will agree that EDM today has little in it for the homebuilder but from time to time, there are tid bits of useful info. You have to read close but I have...
I will agree that EDM today has little in it for the homebuilder but from time to time, there are tid bits of useful info. You have to read close but I have...
Just got off the phone with All Electronics and they are currently out of stock for the photo flash capacitors. I have looked on a couple of other "surplus...
Errol, have you tried asking for them at the photo finishers places? The shoot, process & toss cameras are mostly just trashed. I got a sack full. No problem....
Try a place called Electronic Goldmine, www.goldmine-elec.com. They have the photoflash caps listed. I have bought from them for several years. charlie...
Hi all, Radio Shack parts are unavailable in our part of the world (South Africa) and I am therefore forced to search for alternative suppliers/parts (part of...
... Africa) and I am therefore forced to search for alternative suppliers/parts (part of the fun!). I have the opportunity to order a customer specified...
[sic 70 volts 10 amps transformer] ... Should a higher value resistor be used in order to limit the current to 5A or could the existing resistor be used,...
... Dave, Thank you for replying. From your answer I deduct that you will allow the current to be higher than the existing design's 5A? I was wondering whether...
A couple of things you guys need to keep in mind. The only time the resistors really see full load is during a shorted condition. The servo motor should react...
... allow the current to be higher than the existing design's 5A? If you limit the current to 5A, then there is no reason to have a power supply larger than 5A...
Hi Deon, when you contact your transformer supplier, tell them what you intend to use it for and see if they will offer a de-rating value. When using a high...
I agree Dave I don't have any problem with that I will encourage any member on the EDMHomeBuilders group to participate on this list as well. I just wanted to...
Hi Dave, Ben, Thanks for all the feedback. I have however decided to rather stick to the book and use a 50V transformer. My knowledge about electronics is just...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
