who of the members is busy are try to build a EDM wire machine? I have machine that work and I like to now who is busy whit that kind of stuff? you can look to...
who of the members is busy are try to build a EDM wire machine? I have machine that work and I like to now who is busy whit that kind of stuff? you can look to...
Fantastic work. Do you have a website that gives more details on the hardware and electronics. What all materials have you cut with it. I noticed you had some...
Hello about you quistions the material that I have cut at the moment is steel, stanless steel, copper, brass, titaan, aluminium. about the website, at the...
Hello about you quistions the material that I have cut at the moment is steel, stanless steel, copper, brass, titaan, aluminium. about the website, at the...
Hello about you quistions the material that I have cut at the moment is steel, stanless steel, copper, brass, titaan, aluminium. about the website, at the...
The Group meets on the third Sunday each month (this month Sunday 19th APRIL, 2009) - at: McDonalds McCafe Corner Canning Highway and Berwick Street Victoria...
WOW Benny, That's some impressive machine you've made there. Is the CNC part on a direct feed back from the sparking voltage, or does it just go slowly on...
Benny, That is a very impressive machine. Thank you for posting the link and pictures. I have built a few sinker EDMs, and I am collecting parts to build a...
Hello, My local photo processor was more than happy to give me a handful of used one-use cameras with flashes containing the necessary capacitor for Ben's EDM...
A screwdriver? Actually, I imagine any 1/2W decently-high value resistor would work fine. They'll give you a nice jolt, but won't kill you. I asked before,...
Nick just tell them that you are looking for some camera parts to experiment with kind of like a science project, If there were a liability issue you would not...
No, I live in NM, but that was in the city of Denver, bastion of commies. ... -- Nick A "You know what I wish? I wish that all the scum of the world had but a...
I've crossed them with my fingers and it hurts (don't like to do it hurt, not need-resuscitation hurt). There's less than 100 mJ in those little guys, but it ...
a^b is a to the b power. 10^2 = 100. I'm not sure what kind of voltage you're looking at, I'd guess something less than 50,000 volts. The formula for power is...
The servo up and servo down buttons essentially override the reference pot by pulling it high or low. One leg of each momentary switch goes to the wiper of the...
I have just posted a schematic of the edm relay setup that I made in pics folder (Mikes edm) It will let you use just about any DC motor that you want to use,...
... This was my initial discovery with these units and it made me let go in big hurry. One of the problems with disassembly of the one-use cameras is that if...
You can easily parallel capacitors to get increased capacity. The smaller ones will carry proportionately less current (80uF will only carry 2/3 of the...
Hallo Jay About you questions, The cutting speed of the wheel is 0,5mm/min and the thickness is 15mm steel. The cutting speed of Stainless steel of 6mm is...
I have seen the internet site, but there stay notting new on it, the esencial things is always missing. The parameters. And on the generator that you...
I have place by the photo a table of the paramets. Scanner 0005 _____ From: EDMHomeBuilders@yahoogroups.com [mailto:EDMHomeBuilders@yahoogroups.com] On Behalf...
Hello Julio About the power supply is build up whit transistors, a transformer, op amps, digital IC 7400 serie , opto coupler, capacitors and resistors., but I...
Dear Cristian, I´m very intersted in Garden circuit and want to follow your experience send me an email to sologurenjulio@.... I can´t understand how...
... I don't have the circuit in front of me at the moment but from memory the 555 in Garden of EDM was used to make the high voltage for the gate of the high...
Hey people -- use Google -- it is not rocket science. www.google.com I searched for this: "Garden of EDM" And the page of the guy who developed it came up as...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
