Radiation Detection Probes and Their Dial Scales> A Tutorial by Geo

Pay attention to the Gamma Sensitivity numbers in the specification sheets and charts. This figure gives a clue as to how sensitive a certain tube is compared to another tube or probe. The number indicates how many pulses you would get from a uniform flux of Cs-137, in counts per minute/per mR/H. Each probe must use a dial scale that is correctly delineated for the CPM/mR/H of that probe. Only LUDLUM MEASUREMENTS makes dial scales that are easily changed to match their respective probes. NOTE: The mR/H scale is ONLY accurate when measuring Cs-137, OR when using an energy compensated probe (44-38).

                       
For all probes except the few specifically labeled “Energy Compensated”, the other factor is Gamma Energy Response> different tubes and probes  will respond to varying energy levels according mainly to he construction materials used, and volume and pressure of fill gas or crystal (size of probe). In general, Low Energy Gammas (LEG) must be of sufficient strength (meaning energy level, not number of disintegrations) to penetrate the housing material. A Z number is used to indicate density of any material, based on atomic makeup. Some probes utilize LOW Z windows to allow in extra low energy rays and particles.

Once inside the tube, lower energy Gammas are much more likely to cause an interaction, and therefore be counted. At some point as the energy level increases, the ray will simply pass out of the tube and not be counted. These facts account for the whipsaw shape of the energy response curves of all GM tubes. External filtering may be applied to compensate for this non linear effect, resulting in a probe that is called" energy compensated". Be aware that this procedure knocks all the response down to the lowest level, and that although now nearly perfectly linear, such a probe will give lower reading than you may be used to from the more common "energy dependant" probes.

Making a rough estimate of activity may be found by applying this formula:
@1 meter 1Ci= .381 R

where 1uCi=10^-6 Ci

and using the inverse squared law:
@ 1/2 meter = X4
@1/4 meter = X 16
@ 1/8 meter= X64
@ 1/16 meter = X256
etc.

1 uCi is always equal to 3.7 X 10^4 DPS (disintegrations per second) or 2.22 X10^6 DPM no matter what type of radiation is involved.
http://www.sizes.com/units/curie.htm
http://www.radcon.arizona.edu/training/RSPC-CH.pdf

When the term 4Pi is used, it refers to disintegrations in all directions, as in a sphere. Most probes can only see from one
direction and as such are 2Pi (1/2 of a sphere). GEOMETRY is the term used to indicate the area that the radiation fills in relation to the probe. Technically it is the angle subtended by the probe.
Best geometry is achieved if the probe is 10X it's own diameter away from the source.
4Pi or near 4Pi can be achieved with hollow probes (as in WELL probes) where the radioactive sample is placed inside. Liquid scintillators are also 4Pi, as the sample is inside the liquid.

 

 

   

202-330
0-4k cpm; 0-2 mR/hr
For Model 44-7 

 

 

202-241
0-2 mR/hr; 0-2.4k cpm
For Model 44-6; 44-38

 

 

 

 

 202-654
0-50 mR/hr; 0 - 8.5k cpm
For Model 44-2

 

 

 

 

 

202-717
0-5 mR/hr
For Model 44-10

 

 

202-212
0-5 mR/hr; 0-3500 cpm
For Model 44-3(I-125)

 

LOW ENERGY GAMMA (LEG) Probes have a thin crystal, making them more like"non-high energy detectors".

Since low energy Gammas and X-Rays are absorbed in the first 1/100th of an inch in NaI(Tl), there is no need to make the crystal any thicker than that.

Without a thick crystal, high energy rays are not well absorbed, therefore add little to the desired signal.

In addition most LEG probes incorporate some sort of thin entrance window, making it easier for the LEG to penetrate into the crystal.

 

 

 

George Dowell

New London Nucleonics Laboratory

Copyright © Viscom Inc. 2007

The treatise may under no circumstances be resold or redistributed in either printed, electronic,

or any other forms, without prior written permission from the author.

Comments, criticism and questions will be appreciated and may be directed to

the author by email to GEOelectronics@...