Yep, the LED's they used where: Kingbright L-7113UVC. That particular LED has a 20 degree "beam", they put 24 of them in a grid ~32mm appart. The distance from...
16171
Homebrew_PCBs@yahoogr...
Oct 1, 2006 6:57 pm
Monthly Reminder, please read: Messages and threads: Please do NOT start a new thread by replying to another message. Even if you change the subject line...
Hi Stefan, I had been using 3M 33+ because it is very stretchy compared to other electrical tapes, and it conforms well. I have been running my fingernail...
On Mon, 02 Oct 2006 01:28:16 +0200, kilocycles <kilocycles@...> ... Simply do not remove the paper from the other side. I used to align two papers, put...
... Odd that you use so much heat, I was having problems with the toner not transfering to the board so used ore heat, it got better, I then 'uprated' the...
Jam5411's recent EUREKA moment with using the Simple Green wipes on a inkjet printed pcb got me to thinking. There has been a lot of discussion on the best...
Yes, the thing is, this is easy to over-do. If you apply too much, say propylenglycol, you'll get ink running all over the place. BTW diluted ink (from a...
Sigh.... You missed the point again, Steffie. Once you have identified a property, and have a tool to measure the effects, the tool can be used to optimize the...
On Mon, 02 Oct 2006 19:59:17 +0200, Myc Holmes <mycroft2152y@...> ... Well, Mycie, i don't mind having another test to quantify the effects of wetting...
... Hi Chris, I've been working on it on and off. Toner transfer works well for me so this is more oF a 'as time permits and I need a break from something...
... ST said something about failed tests not completly cleaned from the copper affecting the inkjet tests. I found something similar with toner transfer. (way...
Hello all, Does anyone know what silkscreen ink I should use for making solder resists (mask)? I have made many prototypes, but a nice thing to have would be a...
... A UV hardened material specifically intended for the purpose perhapse? http://www.thinktink.com/stack/volumes/voli/store/specs/8130spec.htm You expose and...
Andrew, I would think that the minimum purchase of one $200+ roll (40 ft by 12") puts the technology out of the range of most hobbyists. There is a big ...
... No - sorry. Don't know where to buy smaller ammounts. There will be cheaper places than think-tink but thats the smallest size I imagine. I would have...
Hi guys, About a year ago or so there was some talk of using EDM for isolation milling and such. Stefan was tinkering a bit with it and another fellow did some...
I was curious about the stuff sold for removing ferric chloride stains, so I looked up the Mega Electronics data sheet on the stuff they sell (its made by...
... Sure thing Chris, I started an EDM project about the same time the list was started. The reasons for choosing raster instead of vector were twofold. ...
On Tue, 03 Oct 2006 14:42:16 +0200, leon_heller ... I am told a little hydrochloric acid does the job too, but haven't tried myself. Prior to learning that i...
Hi Curt, Good to hear from you again. The reason I am continuing to build a small EDM PCB Mill is because the machine can be left on it's own to plug away at...
On Tue, 03 Oct 2006 21:43:41 +0200, roger lucas <ralucas4277@...> ... I dunno, but i'd say it will at least require a few goats and voodoo dolls! How...
In article <efenve+kenr@eGroups.com>, ... Probably because your comment appears to be to John's post, at least ... Please watch your language and your temper. ...
In a message dated 10/3/2006 2:33:18 P.M. Central Daylight Time, stefan_trethan@... writes: I am told a little hydrochloric acid does the job too, but...
In article <000801c6e729$c819fea0$0401a8c0@LEON3>, ... The commercial FeCl3 stain remover I purchased (RS Components in the uk, or maybe Farnell) contains...
... I spoke to him off list and we've got it all sorted out. I was upset at Derek for baiting, and John for taking the bait. It didn't help that one of my...
I've just made a PCB which uses a Mega8 AVR in the LQFP package. I don't tin my boards, and usually solder the leads of that sort of chip one at a time after...
Hi all, with this question I pick the occasion in order to introduce to me, I write from Italy, use for my designs Circad, therefore we can exchange ...
