Hi, I remember reading in a post, a while ago, that after transfering the toner to the PCB, u could seal it with a heat gun, eliminating the porous surface,...
As the original poster, I simply used a hair dryer very close to the durace of the pvb to "fast fuse" the toner. Yes it works with the sponge method. I've also...
Thnx for the replies, I am going to test it. Gonna try a hot air gun and the label backing paper.Hopefully the gun will work. Thnx again ... durace ... is to...
Thanks Javaguy, a picture is worth a thousand words. I have never used the soda wash product before but now that I see the box I am sure I can find it at the...
The laminator cost me about $100, but there are less expensive ones. Your 4x6 may get hot enough. Never hurts to try. From what I have read you will have to be...
... You want the side you removed the plastic from down on the board. The mylar side is up. I may need to make a correction to my descriptions. I said that the...
Hi Markus, I have another question. In Bungard catalog is price for 500ml of Activator(Catalist). Is it suppose that it need to be mixed with 2l of something...
Suske, With the chemistry from Bungard it's like this: Bath #1, #4,#5 are "on their own". That said you must mix each of them according to the information you...
... Hey Javaguy, Great pic's, very descriptive! The process for getting this on the board looks pretty easy if you have the right laminator. One question,...
Hi Markus, Thanks a lot for your writing. Another detail ar fluid heating. Bungard use PTFE plated large area heaters. What did you use for fluids heating...
Hi Suske, I obviousely don't care too much from where you get the chemistry as long as it hopefully works out well for you :-). In other words, I apreciate the...
" what company makes the photoresist" "I purchased the photoresist from thinktink.com, but the smallest amount they sell is in 80 foot rolls." Phil, If you ask...
Hello, For Anodes copper, very necesary use "PHOSPHORIC COPPER" For me, after 20 year using electrolitic copper bath, is no heating, to min 15° centigrade. ...
Patrick, Your input is highly apreciated. However, I made the experience that wiht the very small tanks I use (remember, 4 liters for the copper solution, 2...
Markus, I appreciate your reflexion for copper electroiltic bath. For me, English is not simple... Yes, this is a problem to obtain a good result in small...
Greetings all. I am working on a website that brings builders, programmers, designers, electronics wizards and such all together in one place to network with ...
Patrick, First off, your english is better than my french :-) Many thanks for taking the effort! Thanks for the insight here. I'm lucky enough to have...
Ok Markus, All i have describe is an industry process but perhaps you can apply somme partial to your labo for electronic developement. No, we d'ont use two...
Hello Everyone, I lurk and learn, but today, I just had to ask a question. I subscribe to http://www.instructables.com/ . Today I came across someone who...
I would love engineering issues and news, along with the latest on any tech topic including Wall-E. But if you have a SPECIFIC topic you would like to author,...
It was an answer to a question. And it wasn't really spam, I am looking for someone to write articles about what is going on here and the latest news about...
The question that was asked about the project was sent as a forward, so when I replied I went to the bottom and hit reply via webpost without realizing it was...
... Possibly, but: 1) static charge on a solid metal object accumulates at the edges. Getting a decent coat would be difficult. 2) the laser diode would have...
Patrick and Markus, THANK YOU ! I am following this group for more than one year but your revealings shared here it is the first professional information that...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
